Craftsman T1600 Manual Del Operador página 20

7.
8.
9.
r
Movethe tractor'sPTO (Blade Engage) intothe ONposition.
Remain inthe operator's positionwith the cuttingdeck engaged for a
minimumoftwo minutes, a llowingthe underside of the cuttingdeck to
thoroughlyrinse.
Movethe tractor'sPTO (Blade Engage) into the OFF position.
10.
11.
Figure 12
Turnthe ignitionkeyto the STOP p ositionto turn thetractor'sengine off.
Turnthe wateroff anddetachthe hosecouplerfromthe waterport onyour
deck's surface.
12. Repeat s teps4through11onthe opposite sideof the cuttingdeck.
IM PORTANT: Aftercleaning yourdeckwiththe Deck Wash System
TM,
return
to the operator's positionandengage the PTO. K eep the cuttingdeckrunningfor a
minimumof two minutes, a llowingthe underside of the cuttingdeck to thoroughly
dry.
Adjustments
Neverattempt to makeany adjustmentswhile the engine is running, except
wherespecified inthe operator'smanual.
Levelingthe Deck
NOTE: Check thetractor's t irepressure before p erforming anydeck leveling
adjustments. Refer toTires i n theService section o fthismanual formore
information r egarding tirepressure.
Front ToRear
Thefront ofthe cuttingdeckissupported byastabilizerbarthatcanbeadjusted to
levelthe deck from front to rear. T hefront ofthe deckshouldbebetween1g-inch
and3/8-inchlowerthanthe rearof the deck.Adjustif necessary a sfollows:
1. Withthe tractorparkedon afirm, levelsurface, p lace the leverforlifting the
platformonthe second to the top notch(second highestposition)androtate
the bladeasclose aspossible tothe discharge channel t hat isparallel t o the
tractor.
2. Measure t he distance fromthe front of the bladetip to thegroundandthe
rearof the bladetip to theground.The first measurement takenshould
bebetweenlg" and3/8"lessthanthe second measurement. Determine
the approximate distance necessary f orproperadjustment a ndproceed, if
necessary, to the nextstep.
3. Locate the flangelocknut onthe front sideof the stabilizerbracket. S ee
Figure 13.
Tightenthe flangelocknut to raise the front of the deck;
Loosen the flangelocknut to lowerthe front of the deck.
f
J
J
Figure13
Side to Side
Ifthe cuttingdeckappears to be mowingunevenly, asideto sideadjustmentcanbe
performed. A djustif necessary asfollows:
1. With the tractorparked on afirm, levelsurface, p lacethe decklift leverin
the second from the top notch(second highestposition)androtateboth
blades sothattheyareperpendicular with the tractor.
2. Measure t he distance fromthe outsideofthe left bladetip to theground
andthe distance from theoutsideof the right bladetip to the ground.Both
measurements takenshouldbeequal.Ifthey'renot,proceed to the next
step.
3. Loosen, but do NOT remove, t he hexcapscrewonthe left deckhanger
bracket. S eeFigure 14.
4. Balance t he deckbyusingawrenchto turn the adjustment g ear(found
immediately behindthe hexcapscrew just loosened) c lockwise/up or
counterclockwise/down. Thedeckisproperlybalanced whenbothbladetip
measurements takenearlierareequal.
5. Retighten the hexcapscrewonthe left deckhangerbracket w henproper
adjustmentisachieved.
2O