Publicidad
Idiomas disponibles
Idiomas disponibles
INSTALL
DUST COLLECTION
BAG
Dust collection system consists of a 30-micron bag and
clamp.
•
Place clamp over bag sleeve (see Figure 4).
•
Slide sleeve with clamp over dust chute. Rotate han-
dle to increase clamp size.
•
Secure in position by tightening clamp. Do not force
handle.
Rotate
to Enlarge
Clamp
Figure
4 - Attach
Dust
Collection
Bag
Refer to Figures 5, 6 and 7.
MOTOR
The 120 Volt AC motor has the following specifications:
Horsepower (Maximum Developed) .............
2/5
Voltage ...................................
120
Amps .....................................
2.3
Hertz .....................................
60
Phase ..................................
Single
RPM ....................................
1725
POWER SOURCE
The motor is designed for operation on the voltage and
frequency specified. Normal loads will be handled safe-
ly on voltages not more than 10% above or below the
specified voltage.
Running the unit on voltages which are not within the
range may cause overheating and motor burn-out.
Heavy loads require that the voltage at motor terminals
be no less than the voltage specified. Power supply to
the motor is controlled by a single pole locking rocker
switch. Remove the key to prevent unauthorized use.
GROUNDING
INSTRUCTIONS
WARNING:
Improper connection of equipment
grounding conductor can result in the risk of electrical
shock. Equipment should be grounded while in use to
protect operator from electrical shock.
Check with a qualified electrician if grounding instruc-
tions are not understood or if in doubt as to whether the
tool is properly grounded.
This tool is equipped with an approved 3 conductor
cord rated at 150V and a three prong grounding type
plug for your protection against shock hazards.
Grounding plug should be plugged directly into a prop-
erly installed and grounded 3-prong grounding-type
receptacle, as shown (Figure 5).
Properly
Grounded
Outlet
Grounding
Prong
3-Prong
Plug__
Figure
5 - 3-Prong
Receptacle
Do not remove or alter grounding prong in any manner.
In the event of a malfunction or breakdown, grounding
provides a path of least resistance for electrical shock.
WARNING:
Do not permit fingers to touch the termi-
nals of plug when installing or removing from outlet.
Plug must be plugged into matching outlet that is prop-
erly installed and grounded in accordance with all local
codes and ordinances. Do not modify plug provided. If it
will not fit in outlet, have proper outlet installed by a
qualified electrician.
Inspect tool cords periodically, and if damaged, have
them repaired by an authorized service facility.
Green (or green and yellow) conductor in cord is the
grounding wire. If repair or replacement of the electric
cord or plug is necessary, do not connect the green (or
green and yellow) wire to a live terminal.
Where a 2-prong wall receptacle is encountered,
it
must be replaced with a properly grounded 3-prong
receptacle installed in accordance with National Electric
Code and local codes and ordinances.
WARNING:
This work should be performed by a quali-
fied electrician.
A temporary 3-prong to 2-prong grounding adapter (see
Figure 6) is available for connecting plugs to a two pole
outlet if it is properly grounded.
Grounding
Lug
_======_
Make Sure
Adapter
_
"_..._J
This Is
3-Prong Plug
\ ((I
II Connected
To
\
I
II AKnown
_
Ground
2-Prong
Receptacle
Figure
6 - 2-Prong
Receptacle
with
Adapter
Do not use a 3-prong to 2-prong grounding adapter
unless permitted by local and national codes and ordi-
nances. (A 3-prong to 2-prong grounding adapter is not
permitted in Canada.) Where permitted, the rigid green
4
Publicidad
