Samsung 5 Serie Manual Del Usuario página 37

Listening through a Receiver (Home theater)
You can listen to sound through a receiver instead of the TV speaker.
1. Press the TOOLS button. Press the ENTERI--I# button to select Anynet + (HDMI-CEC).
2. Press the A or T button to select Receiver. Press the 4 or _. button to select On or Off.
3. Press the EXIT button to exit.
If your receiver supports audio only, it may not appear in the device list.
The receiver will work when you have properly connected the optical in jack of the
receiver to the DIGITAL AUDIO OUT (OPTICAL) jack of the TV.
When the Home Theater receiver is set to On, you can hear sound output from the
TV's Optical jack. When the TV is displaying a DTV(air) signal, the TV will send out
5.1 channel sound to the Home theater receiver. When the source is a digital component such as a DVD and is connected
to the TV via HDMI, only 2 channel sound will be heard from the Home Theater receiver.
If there is a power interruption to the TV when the Receiver is set to On (by disconnecting the power cord or a power
failure), the Speaker Select may be set to External Speaker when you turn the TV on again.
Troubleshooting for Anynet +
Problen_ Possible Solution
Anynet + does not work. • Check if the device is an Anynet+ device. The Anynet + system supports Anynet+
devices only.
• Connect only one receiver (home theater).
• Check if the Anynet+ device power cord is properly connected.
• Check the Anynet + device's Video/Audio/HDMI 1.3 cable connections.
• Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
• Check whether the TV remote control is in TV mode.
• Check whether it is Anynet+ exclusive remote control.
• Anynet + doesn't work in certain situations. (Searching channels, Operating, Plug & Play,
etc.)
• When connecting or removing the HDMI 1.3 cable, please make sure to search devices
again or turn your TV offand on again.
• Check if the Anynet+ Function ofAnynet + device is set on.
I want to start Anynet+, • Check if the Anynet+ device is properly connected to the TV and check if the Anynet+
(HDMI-CEC) is set to On in the Anynet + Setup menu.
• Press the TV button on the TV remote control to switch to TV. Then press the TOOLS
button to show the Anynet + menu and select a menu you want.
I want to exit Anynet +, • Select View TV in the Anynet + menu.
• Press the SOURCE button on the TV remote control and select a device other than
Anynet + devices.
• Press v CH A, CH LIST, PRE-CH, and FAV.CH to change the TV mode. (Note
that the channel button operates only when a tuner-embedded Anynet + device is not
connected.)
The message Connecting to • You cannot use the remote control when you are configuring Anynet+ or switching to a
Anynet + device.,, appears on the view mode.
screen. • Use the remote control when the Anynet+ setting or switching to view mode is complete.
The Anynet + device does not • You cannot use the play function when Plug & Play is in progress.
play.
The connected device is not = Check whether or not the device supports Anynet+ functions.
displayed, • Check whether or not the HDMI 1.3 cable is properly connected.
• Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
• SearchAnynet + devices again.
• You can connect an Anynet+ device using the HDMI 1.3 cable only. Some Some HDMI
cables may not support Anynet+ functions.
• If it is terminated by an abnormal situation such as disconnecting the HDMI cable or
power cord or a power failure, please repeat the device scan.
The TV program cannot be • Check whether the antenna jack on the recording device is properly connected.
recorded,
• Connect the optical cable between TV and the receiver. The TV sound is not output
through the receiver,