Publicidad
Idiomas disponibles
Idiomas disponibles
5. TWO-SPEED GEAR CONTROL (SEE FIG. G, H)
The drill has a two-speed gear control designed for drilling or
driving at LO (mark is 1) or HI (mark is 2) speeds. A slide switch
is located on top of the drill to select either LO or HI speed. When
using the drill in the LO speed range, the speed will decrease and
the drill will have greater power and torque. When using the drill
in the HI speed range, the speed will increase and the drill will
have less power and torque.
Gear I
Low speed range: for screwdriving or working with large drilling
diameter.
Gear II
High speed range: for working with small drilling diameter.
move the rotation control to the right.
WARNING: When overload occurs frequently on the
high speed gear, switch to the low speed gear to
avoid the motor overheating.
6. CHUCK ADJUSTMENT (SEE FIG. I)
To open the chuck jaws rotate the front section of the chuck.
Insert the drill bit between the chuck jaws and rotate the front
section in the opposite direction. Ensure the drill bit is in the
center of the chuck jaws. Finally, firmly rotate the front chuck
section in the opposite directions. Your drill bit is now clamped
in the chuck.
7. TORQUE ADJUSTMENT (SEE FIG. J)
(Screw driving force of your drill driver)
The torque is adjusted by rotating the torque adjustment ring.
The torque is greater when the torque adjustment ring is set on
a higher setting. The torque is less when the torque adjustment
ring is set on a lower setting.
Make the setting as follows:
1-4
for driving small screws
5-9
for driving screws into soft material
10-14
for driving screws into soft and hard material
15-19
for driving screws into hard wood
20
for driving larger screws
for heavy drilling
8. USING BELT CLIP (SEE FIG. K)
Screw the Belt clip on the tool with the screw . The Belt clip can
be hooked on your belt or pocket, etc.
9. USING THE SIGHT LIGHT
To turn on the light, press the on/off switch and make sure the
forward/reverse rotation control is on right/left position. When you
release the on/off switch, the light will be off.
LED lighting increases visibility-great for dark or enclosed area.
10. DRILLING
When drilling into a hard smooth surface, use a center punch to
mark the desired hole location. This will prevent the drill bit from
slipping off center as the hole is started.
Hold the tool firmly and place the tip of the bit at the point to be
drilled.
Depress the switch trigger to start the tool.
Move the drill bit into the workpiece, applying only enough
pressure to keep the bit cutting. Do not force or apply side
pressure to elongate a hole.
EN
Tungsten carbide drill bits should always be used for concrete
and masonry. When drilling in metal, only use hss drill bits in
good condition. Always use a magnetic bit holder when using
short screwdriver bits. When screw-driving, apply a small
quantity of liquid soap or similar to the screw threads to ease
insertion.
11. OVERLOAD PROTECTION
When overloaded, the motor comes to a stop. Relieve the load on
the tool immediately and release the on/off switch. Restart the
tool as normal.
12. TEMPERATURE DEPENDENT OVERLOAD
PROTECTION
When using as intended for the power tool cannot be subject
to overload. When the load is too high or the allowable battery
temperature is too hot, the electronic control switches off the power
tool until the temperature is in the optimum temperature range
again.
13. DISPOSAL OF AN EXHAUSTED BATTERY PACK
To preserve natural resources, please recycle or dispose
of the battery pack properly. This battery pack contains
Lithium batteries. Consult your local waste authority for
information regarding available recycling and/or disposal options.
Discharge your battery pack by operating your drill, then remove
the battery pack from the drill housing and cover the battery
pack connections with heavy-duty adhesive tape to prevent short
circuit and energy discharge. Do not attempt to open or remove
any of the components.
PROBLEM SOLUTION
1. Why does the drill not turn on when you press the switch?
The forward/reverse rotation control, which is on top of the
trigger, is positioned in the lock function. Unlock the forward/
reverse rotation control by putting it into the required rotation
position. Push the trigger and the drill will start to rotate.
2. THE DRILL STOPS BEFORE THE SCREW IS COMPLETELY
TIGHTENED. WHY?
Verify the torque position of the torque adjusting ring, you can
find the torque-adjusting ring between the chuck and the drill
body. Position 1 is the lowest torque (screw driving force) and
position 20 is the highest torque (screw driving force). Position
is for drill operation. Regulate the torque adjusting ring to a
higher position to reach the best result.
3. I CANNOT FIT THE BATTERY INTO THE BATTERY CHARGER.
WHY?
The battery can be inserted into the charger only in one direction.
Turn the battery around until it can be inserted into the slot.
4. REASONS FOR DIFFERENT BATTERY PACK WORKING TIMES
Charging time problems, and having not used a battery pack for
a prolonged time will reduce the battery pack working time. This
can be corrected after several charge and discharge operations
by charging & working with your drill. Heavy working conditions
such as large screws into hard wood will use up the battery pack
energy faster than lighter working conditions. Do not re-charge
your battery pack below 0oC and above 40oC as this will affect
performance.
11
Publicidad
