Thermis THS-90 Instrucciones De Uso página 2

INSTRUCTION MANUAL
cased stem thermostat THS-90/210
Description and use
Stem thermostats THS 90/210 are designed for operation of electric appliances
depending upon temperature of measured medium. Mounting is performed into
heating system using copper protection well with thread G1/2. Suitable material is
used for joint sealing, preferably teflon tape. Maximum permissible pressure on the
well is 10bar (1 Mpa). Made in wide range of temperature ranges. Standard stem
length is 100mm (in case of need 200, 300mm). Thermostat case guarantees
protection IP 40 .
Design Instalace
c
Dimensions in mm
a b c
9 2 20 5 5
f g h
6 10 100
Installation Instalace
Warning:
Only qualified person can do installation and connection of thermostat to integrated
circuit in accordance with notice nr.50/1978 mim.§ 6.
Installation only without voltage!
1. Install thermostatic well into relevant process connection with G1/2 thread
(weld-on piece). Use teflon tape or other appropriate gasket fork sealing.
2. Loosen four fixation screws 2 (do not remove big button).
3. Remove frontal case 3 including regulatory button 1 .
4. Thread the connected conductor through power supply bushing 4 , and tighten
attached conductor to thermostat clamp a , b , c , according to requested
function.Connect ground cable to ground clamp 4 .
5. Put on frontal case 1 and tighten four fixation screws 2 .
Storing conditions Instalace
Storing can be done in closed and aired rooms within temperature range
15–60 °C. Storing and trasfer must not cause a mechanical damage of the
device. Thermostats must be treated with care, with no major shocks or
vibrations.
Disposal Instalace
Disposal should be performed as follows: Hand into a recycling collection
point.
Warranty Instalace
Provided, that the product has been placed and used according to the
instruction manual, the manufacturer provides with warranty in compliance
with a valid code, unless agreed otherwise.
Description
2
1
3
4
i j
d e
10 40
i j
8 44
a
b c
d
a clamp c
1 regulatory button
b clamp 2
2 fixation screw
c clamp 1
3 case
4 power supply bushing d ground clamp
The manufacturer will reject warranty repair, in case the product has been
damaged:
during tranport and storage of the purchaser, or his customers,
-
during installation or disassembly of device of the purchaser or his
-
customer.
Warranty and post-warranty repairs Instalace
Warranty and post-warranty repairs are provided by the manufacturer. Warranty
claim of a faulty thermostat should be done at the seller. The warranty claim will be
accepted in case, that following requirements are met:
submitted warranty list of the given thermostat,
-
paid invoice of the thermostat,
-
the conditions and requirements of operating manual were met.
-
Instalace
Wiring diagram
+°C
° ° °
C -1 switch-off at reaching adjusted temperature
1
C -2 switch-on at reaching adjusted temperature
U
C
2
L
N
PE
Certificate of conformity:
For evaluation of conformity was used protocol nr.6450-004/2009
Harmonized norms: ČSN EN 61010-1:2003, ČSN EN 60695-2-11:2001
info@thermis.cz, www.thermis.cz
Technical parameters
T ype THS-90
Temperature range 0-90°C
Temperature difference 5K
IP protection IP40
Insulation class I
Rate of temp. change <1K/min
Stem length 100-300 mm
Storing temperature 15-60°C
Contacts
switch-on or switch-off
Contact load C-1=16( )A/250V~
C-2 6(1) 400
T case surrounding 80°C
max
T sensor 125°C
max
Mounting well D8mm with thread G1/2
Design
freely accessibly or covered regulation
THS-210
40(70)- 210 °C
5K
IP 0 4
I
<1K/min
100-300 mm
15-60°C
switch-on or switch-off
4
= A/ V~
80°C
245°C