Publicidad
Idiomas disponibles
Idiomas disponibles
2. OPERATING TRANSMITTER:
Operating the buttons on the panel of the transmitter.
3 key -for fan high speed.
2 key-for fan medium speed.
1 key-for fan low speed.
OFF key-for fan off.
LIGHT key-for light on and off.
2hr , 4hr , 8hr button to set the FAN sleep timer
YOUR REMOTE NOW HAS FULL CONTROL OF THE FAN AND LIGHT.
3.TROUBLE SHOOTING GUIDE
a.Power to receiver?
b.Receiver wired correctly?
c.Fan manual speed control in highest position?
d.Light kit switch turned on?
e.Good battery in the transmitter?
If there are two or more ceiling fans installed in the same house, in order to prevent your ceiling fans from being affected by the
remote control of the adjacent ceiling fans, first turn the switch in each remote control transmitter to the CODE(UP) position (see the
schematic diagram FIG1) Remarks: The standard state of the transmitter is in the down code COM.
(Power-off means you need to use a wall switch to shut down the power of the ceiling fan, if you do not have a wall switch,
please power off the whole room from the air circuit-breaker for each room)
After installing the remote control receiver on the ceiling fan
1: Turn on the power of the 1# ceiling fan receiver (the power of the 2# receiver is kept in a power-off state), within 30 seconds after
the fan power is turned on, press the LEARN button corresponding to the 1# transmitter, then The receiver will learn the transmitter code.
When the transmitter code is learned successfully, the light of the ceiling fans will flash twice, and then it can be used normally.
2: Turn on the power of the 2# ceiling fan receiver (the power of the 1# receiver is kept in a power-off state), within 30 seconds after
the fan power is turned on, press the LEARN button corresponding to the 2# transmitter, then The receiver will learn the transmitter code.
When the transmitter code is learned successfully, the light of the ceiling fans will flash twice, and then it can be used normally.
And so on, only one ceiling fan is powered on each time the corresponding transmitter learns.
After the 1# and 2# remote control transmitters have been successfully learned, turn on the power of the two ceiling fans. At this time,
the 1# transmitter and the 2# transmitter can be used separately for one ceiling fan.
FCC Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions.
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital, pursuant to Part 15 or the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may casue harmful interference to radio communications,
However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
--- Reorient or relocate the receiving antenna.
--- Increase the separation between the equipment and receiver.
--- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--- Consult the dealer or an experienced radio/ TV technician for help.
WARNING:
Do NOT install this fan with variable speed wall
control or wall-mounted dimmer switch. It will
permanently damage the fan's remote control
and cause the fan's function to fail.
Installation & Operating Instructions for the
Parrotuncle Owner's Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
LENARN
CODE
TRANSMITTER
NO Variable speed wall control
F6354110V
MODEL:GA012
OPERATION DISTANCE 20 FEET
ACL
CODE
COM
LENARN
CODE
ANT
RECEIVER
(FIG.1)
NO Dimmer switch
ACN
INPUT
OUTPUT
. . .
Publicidad
