Descargar Imprimir esta página

UNIPRODO UNI HEATER 06 Manual De Instrucciones página 5

Calefactor colgante

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 14
EN
e)
In case of fire, use a powder or carbon dioxide
(CO2) fire extinguisher (one intended for use on
live electrical devices) to put it out.
f)
Use the device in a well-ventilated space.
g)
Please keep this manual available for future
reference. If this device is passed on to a third
party, the manual must be passed on with it.
h)
Keep packaging elements and small assembly
parts in a place not available to children.
i)
Keep the device away from children and animals.
j)
If this device is used together with another
equipment, the remaining instructions for use
shall also be followed.
REMEMBER! When using the device, protect
children and other bystanders.
2.3. PERSONAL SAFETY
a)
Do not use the device when tired, ill or under
the influence of alcohol, narcotics or medication
which can significantly impair the ability to
operate the device.
b)
The device is not designed to be handled by
persons (including children) with limited mental
and sensory functions or persons lacking relevant
experience and/or knowledge unless they are
supervised by a person responsible for their
safety or they have received instruction on how to
operate the device.
c)
To prevent the device from accidentally switching
on, make sure the switch is on the OFF position
before connecting to a power source.
d)
The device is not a toy. Children must be
supervised to ensure that they do not play with
the device.
2.4. SAFE DEVICE USE
a)
Do not use the device if the ON/OFF switch does
not function properly (does not switch the device
on and off). Devices which cannot be switched on
and off using the ON/OFF switch are hazardous,
should not be operated and must be repaired.
b)
Make sure the plug is disconnected from the
socket before attempting any adjustments,
accessory replacements or before putting the
device aside. Such precautions will reduce the risk
of accidentally activating the device.
c)
When not in use, store in a safe place, away from
children and people not familiar with the device
who have not read the user manual. The device
may pose a hazard in the hands of inexperienced
users.
d)
Keep the device in perfect technical condition.
Before each use check for general damage and
especially check for cracked parts or elements
and for any other conditions which may impact
the safe operation of the device. If damage is
discovered, hand over the device for repair before
use.
e)
Keep the device out of the reach of children.
f)
Device repair or maintenance should be carried
out by qualified persons, only using original spare
parts. This will ensure safe use.
g)
To ensure the operational integrity of the device,
do not remove factory-fitted guards and do not
loosen any screws.
8
h)
When transporting and handling the device
between the warehouse and the destination,
observe the occupational health and safety
principles for manual transport operations which
apply in the country where the device will be used.
i)
Do not move, adjust or rotate the device in the
course of work.
j)
Do not leave this appliance unattended while it is
in use.
k)
Clean the device regularly to prevent stubborn
grime from accumulating.
l)
The device is not a toy. Cleaning and maintenance
may not be carried out by children without
supervision by an adult person.
m)
It is forbidden to interfere with the structure of
the device in order to change its parameters or
construction.
n)
Keep the device away from sources of fire and
heat.
o)
Do not overload the device.
p)
Do not cover the ventilation openings!
q)
During operation, some parts of the device heat
up and remain hot for a few minutes after turning
off the device.
r)
Do not cover the heater!
s)
To prevent fire, leave free space around the
device.
t)
When the device is not in use, always unplug it.
u)
The device should not be turned on while sleeping.
v)
For safety reasons, do not use the device with a
programmer or other device that automatically
starts the heater. There is a risk of fire if the device
is not set up correctly and cannot be controlled by
the user.
w)
Do not use the device to dry laundry!
x)
The device can only be installed on the ceiling.
y)
The device may only be operated in an upright
position.
z)
The heater is not intended for use in bathrooms,
laundries and other similar rooms. Never place
the heater in a place where it could fall into a
bathtub or other water tank.
ATTENTION! Despite the safe design of the
device and its protective features, and despite
the use of additional elements protecting the
operator, there is still a slight risk of accident or
injury when using the device. Stay alert and use
common sense when using the device.
3. USE GUIDELINES
The device is designed to heat air on balconies/terraces.
The product is not intended for indoor use!
The product is intended for home use only!
The user is liable for any damage resulting from
unintended use of the device.
3.1. DEVICE DESCRIPTION
1
2
3
5
4
1.
Housing
2.
Heating element
3.
Protective mesh
4.
ON/OFF switch
5.
Remote control
1
2
3
4
1.
ON/OFF switch
2.
POSITION 1: 500 W (normal power)
3.
POSITION 2: 1000 W (medium power)
4.
POSITION 3: 1500 W (maximum power)
3.2. PREPARING FOR USE
APPLIANCE LOCATION
The temperature of environment must not be higher than
40°C and the relative humidity should be less than 85%.
Ensure good ventilation in the room in which the device
is being used. The device should always be used when
positioned on an even, stable, clean, fireproof and dry
surface, and be out of the reach of children and persons
with limited mental and sensory functions. Position the
device such that you always have access to the power
plug. The power cord connected to the appliance must be
properly grounded and correspond to the technical details
on the product label.
The device must be at least 180 cm away from the ground
and at least 30 cm away from the ceiling of the building or
overhanging elements.
ASSEMBLING THE DEVICE
1.
Using a hammer drill, drill the desired number of
holes in the ceiling.
2.
Insert an expansion plug into each hole.
3.
Screw the ceiling hook into the prepared hole
or fix the hook with screws (depending on the
chosen type of hook). CAUTION! This item was not
included in the kit. CAUTION! The lifting capacity
of the hook must be quadruply greater that the
weight of the device!
9
EN
4.
Hang the device at the preferred height with any
ring of the chain.
3.3. DEVICE USE
1.
Connect the plug to the socket.
2.
Turn the device on using the ON/OFF switch.
3.
Set the required power using the remote :
POSITION 1: 500 W (normal power)
POSITION 2: 1000 W (medium power)
POSITION 3: 1500 W (maximum power)
4.
Turn the device off after use.
3.4. CLEANING AND MAINTENANCE
a)
Always unplug the device before cleaning it.
b)
Use only non-corrosive cleaners to clean the
surface.
c)
After cleaning the device, all parts should be dried
completely before using it again.
d)
Store the unit in a dry, cool place, free from
moisture and direct exposure to sunlight.
e)
Do not spray the device with a water jet or
submerge it in water.
f)
The device must be regularly inspected to check
its technical efficiency and spot any damage.
g)
Use a soft, damp cloth for cleaning.
h)
Do not use sharp and/or metal objects for
cleaning (e.g. a wire brush or a metal spatula)
because they may damage the surface material of
the appliance.
i)
Do not clean the device with an acidic substance,
agents of medical purposes, thinners, fuel, oils
or other chemical substances because it may
damage the device.
DISPOSING OF USED DEVICES
Do not dispose of this device in municipal waste systems.
Hand it over to an electric and electrical device recycling
and collection point. Check the symbol on the product,
instruction manual and packaging. The plastics used
to construct the device can be recycled in accordance
with their markings. By choosing to recycle you are
making a significant contribution to the protection of
our environment.
Contact local authorities for information on your local
recycling facility.

Publicidad

loading