Publicidad
Idiomas disponibles
Idiomas disponibles
Other Features
Filter Replace Reminder
When the Filter Replace light turned
on, replace filter and press Reset
Filter and hold for 3 seconds to reset.
A filter is only needed for models that
are not vented to the outside.
Vent Fan
The vent fan removes steam and other
vapors from surface cooking.
Press Vent Fan once for high fan
speed, twice for medium fan speed,
three times for low fan speed or a
fourth time to turn the fan off.
Chef Connect
Use the Chef Connect feature
for connecting your microwave to
a Café range to sync your vent
fan, cooktop surface lights and
clock via Bluetooth technology.
1
You must have a Chef Connect enabled range. To
pair your microwave for the first time, initiate the
Chef Connect process on the Café range. Refer to
the range owner's manual for instructions
2
On the microwave, hold Chef Connect button for 3
seconds. The Bluetooth icon
start flashing as the microwave starts to search and
pair with your Café range. The icon
after pairing successfully.
If a Café range is not found within 2 minutes during
search mode the microwave will stop searching and
the Bluetooth icon
will turn OFF.
On initial setup, the setup protocol will start.
If the Chef Connect feature is enabled the default
settings are as follows:
- Display clock sync: ON
- Auto surface light: ON (HIGH setting)
- Auto vent fan: OFF
- Auto off: 15 minutes
3
Turn the dial to select Surface Light Sync On/Off.
Press the dial to confirm. If on, it allows the
microwave surface lights to turn on at HIGH level
automatically when the paired range's cooktop
burner turns ON. If OFF, the microwave surface
lights will not automatically turn on when a cooktop
burner turns on.
49-7000160 Rev. 3
Surface Light
Press Surface Light once for bright
light, twice for the night light or a third
time to turn the light off.
Automatic Fan
An automatic fan feature protects the microwave from
too much heat rising from the cooktop below it. It
automatically turns on if it senses too much heat.
If you have turned the fan on you may find that you
cannot turn it off. The fan will automatically turn off when
the internal parts are cool. It may stay on for 30 minutes
or more after the cooktop and microwave controls are
turned off.
4
on the display will
will remain ON
Turn the dial to select Vent Fan Sync ON/OFF.
Press the dial to confirm. If ON, it allows the
microwave vent fan to turn on at LOW speed
automatically when the paired range's cooktop
burner turns on.
If OFF, the vent fan will not turn ON
automatically when a cooktop burner is turned on.
Pairing is now complete, the Chef Connect feature
is now on.
NOTE: If there is no sync option selected during set
up, 5 minutes after icon
return to stand-by mode and use the default settings.
After completing the setting per above steps, your
microwaves vent fan and surface light could be set
to turn on automatically when the cooktop burner is
turned on. The cooktop and range clock display will
be synced to display the same time. The vent fan
and cooktop light will be set to automatically turn off
15 minutes after the cooktop burner is turned OFF.
If desired, the light, fan, and auto off settings can
now be changed using option in Settings.
Press Chef Connect once to temporarily turn OFF
communication between the microwave and range.
Press again to turn communication back ON. The
icon
will illuminate when ON.
In the case of an unintended disconnect such as lost
power to the microwave or range the connection will
remain after power resumed. For very short power
interruptions, the power may need to be reset in
order to reconnect
NOTE: To unpair the microwave from the range,
press and hold the Chef Connect button on the
microwave for 3 seconds. The Bluetooth icon will
start to flash. Press cancel or wait 2 minutes for the
flashing to stop. You may need to unpair when the
Café range is replaced or serviced.
turns ON, the units will
25
Publicidad
