Publicidad
Idiomas disponibles
Idiomas disponibles
EN
If automatic levelling is not possible, e.g. because the surface on which the measuring
tool stands deviates by more than 3.5° from the horizontal plane, the laser switches off.
If this is the case, set up the measuring tool in a level position and wait for the self-
levelling to take place.
In case of ground vibrations or position changes during operation, the measuring tool is
automatically levelled again. Upon levelling, check the position of the laser beams with
regard to the reference points to avoid errors arising from a change in the measuring
tool's position.
Cross line mode with tilt function
To access the cross line mode with tilt, switch on the device with the (A-Fig. A) button.
When the laser level is tilted less than 3.5°, it will perform self-levelling.
When the laser level is tilted more than 3.5°, the pendulum system will lock and the level
will enter the cross line mode with tilt.
To indicate that the cross line mode with tilt is on, the laser beam flashes every 3 seconds.
To return to self-levelling mode, simply reposition the laser level at an angle of less than
3.5°.
Working Advice
Only the centre of the laser point or laser line must be used for marking.
f
The size of the laser point/the width of the laser line changes depending on the
distance.
Working with the tightning plier and the telescopic pole (accessories G&H)
The telescopic pole (H) is stable and height adjustable.
Screw the measuring tool to the tightning plier (G) and then to the telescopic pole (H)
or directly on a tripod. Roughly align the tripod before switching on the measuring tool.
Laser Goggles (Accessory E)
The laser goggles filter out ambient light. This makes the light of the laser appear
brighter to the eye.
Do not use the laser goggles as protective goggles. The laser goggles make the
f
laser beam easier to see; they do not protect you against laser radiation.
Do not use the laser goggles as sunglasses or while driving. The laser goggles
f
do not provide full UV protection and impair your ability to see colours.
Target (Accessory F)
The target (F) improve the laser perception particularly on far distances. Its magnetic
base and hole allows to put it everywhere.
5. SERVICE & MAINTENANCE
The FISCHER DAREX machines have been designed to operate over а long period of
time with а minimum of maintenance. Continuous satisfactory operation depends upon
proper machine care and regular cleaning.
Cleaning
Keep the measuring tool clean at all times.
Never immerse the measuring tool in water or other liquids. Wipe off any dirt using a
38
damp, soft cloth. Do not use any detergents or solvents. The areas around the outlet
aperture of the laser in particular should be cleaned on a regular
basis. Make sure to check for lint when doing this.
Faults
Should a fault occur e.g. after wear of a part, please contact the service address on the
warranty card. In the back of this manual you find exploded view showing the parts that
can be ordered.
Environment
To prevent damage during transport, the appliance is delivered in solid
packaging which mainly consists of reusable materials. Therefore please make
use of options for recycling the packaging.
Faulty and/or discarded electrical or electronic apparatus have to be
collected at the appropriate recycling locations
6. WARRANTY
1. FISCHER DAREX products are designed to highest DIY quality standards. FISCHER DAREX
provides a 5 years warranty for its products, from the date of purchase. This warranty applies
to all material and manufacturing defects which may arise. No further claims are possible,
of whatever nature, director indirect, relating to people and/or materiais. FISCHER DAREX
products are designed to highest DIY quality standards.
2. In the event of a problem or defect, you should first always consult your dealer. In most cases,
the FISCHER DAREX dealer will be able to solve the problem or correct the defect.
3. Repairs or the replacement of paru will not extend the original warranty period.
4. Defects which have arisen asa result of improper use or wear are not covered by the warranty.
Amongst otherthings, this relates to switches and motor, in the event of wear.
5. Your claim upon the warranty can only be processed if:
Proof of the purchase date can be provided in the form of a receipt
y
The guarantee card has been completed in full
y
No repairs and/or replacements have been carried out by third parties
y
The tool has not been subjected to improper use (overloading of the machine or fitting
y
nonapproved accessories).
There is no damage caused by external influences or foreign bodies such as sand or
y
stones.
There is no damage caused by non-observance of the safety instructions and the
y
instructions for use.
There is no force majeure on our part
y
A description of the complaint is enclosed
y
6. The warranty stipulations apply in combination with our terms of sale and delivery.
39
EN
Publicidad
