Publicidad
Idiomas disponibles
Idiomas disponibles
EN
20. Have your tool repaired by
an authorized repair agent. This
power tool is in accordance with
the relevant safety regulations. To
avoid danger, electric appliances
must only be repaired by qualified
technicians.
WARMING: Some dust created
by power sanding, sawing grinding,
drilling, and other construction
activities contains chemicals known
to cause cancer, birth defects or
the other reproductive harm. Some
examples of these chemicals are:
Lead from lead-based paints;
Crystalline silica from bricks
and cement and other masonry
products, and
Arsenic and chromium from
chemically-treated lumber (CCA).
Your risk from these exposures
varies, depending on how often you
do this type of work. To reduce your
exposure to these chemicals: work
in a well ventilated area, and work
with approved safety equipment,
such as those dust masks that
are specially designed to filter
out microscopic particles. Avoid
prolonged contact with dust from
power sanding, sawing, grinding,
drilling, and other construction
activities. Wear protective clothing
and wash exposed areas with soap
and water. Allowing dust to get into
your mouth, eyes, or lay on the skin
may promote absorption of harmful
chemicals.
ADDITIONAL SAFETY
INSTRUCTIONS FOR
ROTARY HAMMERS
21. Keep your drill bits sharp for
best and safest performance.
22. When fitting and changing
accessories, always use the
instructions supplied with the
accessory.
23 Always use the side handle
supplied with the tool. Keep a
firm grip on the tool at all times.
Do not attempt to operate this
tool without holding it with both
hands. Operating this tool with one
hand will result in loss of control.
Breaking through or encountering
hard materials such as re-bar may
be hazardous as well.
24. Use clamps or a vice to hold
work piece, if possible.
25. Make sure the power switch is
not "ON" before you plug in. Always
switch OFF before you put your
hammer drill down.
26. Do not force your hammer
drill – it will do a better and safer
job at the speed for which it was
designed.
27. Hold tool by insulated gripping
surfaces when performing an
operation where the cutting tool
may contact hidden wiring or its
own cord. Contact with a "live"
wire will make exposed metal parts
of the tool "live" and shock the
operator.
28. Do not use chisels in any of the
rotation modes, i.e., rotary drilling
and hammer drilling modes. Chisels
may jam causing loss of control.
29. Wear gloves when handling
hammer bits and tools. Hammer bits
and tools get hot during operation.
Gloves and frequent rest periods
will reduce risk of vibration damage
to hands and arms.
30. Keep gloves away from rotating
bits to avoid entanglement with bit
and possible injury.
31. Keep hands and body from
between the tool and wall or post,
etc, to avoid being crushed by the
tool should it twist unexpectedly if
the bits binds.
DOUBLE INSULATION
The tool is double insulated
according with EN50144. Double
insulation means that all the external
metal parts are electrically insulated
from the mains power supply.
This is done by placing insulated
barriers between the electrical
and mechanical components so
as to making unnecessary for the
tool to be earthed. NOTE: Double
insulation does not take the place
of normal safety precautions when
operating this tool. The insulation
system is for added protection
against injury resulting from a
possible electrical insulation failure
within the tool.
ELECTRICAL SAFETY
The electric motor has been
designed for one voltage only.
Always check that the power supply
corresponds to the voltage on the
rating plate.
Warming: Never connect the live
(L) or neutral (N) wires to the earth
pin marked E or
USING AN EXTENSION
CABLE
An extension cable should not be
used unless absolutely necessary.
Use of an improper extension
cable could result in a risk of fire
and electric shock. If an extension
cable must be used, use only those
that are approved by the country's
electrical Authority.
Make sure that extension cord is
in good condition before using.
Always use the cord that is suitable
for the power input of your tool
(see technical data on name plate).
The minimum conductor size is
1.5mm 2.
13
Publicidad
