HIKOKI UL 18DF Instrucciones De Manejo página 10

English
NOTE
MAX position: The maximum inside temperature that
can be reached is 17°C cooler than the outside
temperature (at 25°C outside temperature).
A maximum inside temperature of approx. 60°C can be
reached (at 25°C outside temperature).
ECO position: The energy consumption corresponds to
energy class A+++. The maximum inside temperature
that can be reached is 8–11°C cooler than the outside
temperature (at 23°C outside temperature).
5. Opening / closing the lid (Fig. 5)
Opening: To be able to open the lid: Fold the carrying
handle backwards. Then open the lid backwards.
Closing: Close the lid and fold the carrying handle
forwards.
6. Energy saving tips
– Do not expose to direct sunlight.
– In cooling mode: Use already cooled food and
beverages.
– Do not open the lid longer than necessary, close it
completely.
– Ensure that air can circulate between the food.
DANGER : Disconnect the device from the power
supply. Pull the plug, remove battery. There is the risk of
electric shock!
MAINTENANCE AND INSPECTION
DANGER : Disconnect the device from the power
supply. Pull the plug, remove battery. There is the risk of
electric shock!
1. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws
be loose, retighten them immediately. Failure to do so
could result in serious hazard.
2. Inspection of terminals (tool and battery)
Check to make sure that swarf and dust have not
collected on the terminals.
On occasion check prior, during and after operation.
CAUTION
Remove any swarf or dust which may have collected on
the terminals.
Failure to do so may result in malfunction.
3. Cleaning
DANGER : Make sure that no liquid enters the inside
of the lid to avoid hazards!
When the outside of the device and lid is stained, wipe
with a soft dry cloth or a cloth moistened with soapy
water. Do not use chloric solvents, gasoline or paint
thinner, for they melt plastics.
Vacuum the ventilation slots or clean with a soft brush.
Clean the inside of the container with water and
dishwashing liquid. Dry well.
4. Storage
Store the device and the battery in a place in which the
temperature is less than 40°C and out of reach of
children.
NOTE
Storing lithium-ion batteries.
Make sure the lithium-ion batteries have been fully
charged before storing them.
Prolonged storage (3 months or more) of batteries with
a low charge may result in performance deterioration,
significantly reducing battery usage time or rendering
the batteries incapable of holding a charge.
However, significantly reduced battery usage time may
be recovered by repeatedly charging and using the
batteries two to five times.
If the battery usage time is extremely short despite
repeated charging and use, consider the batteries dead
and purchase new batteries.
CAUTION
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
Important notice on the batteries for the HiKOKI
cordless power tools
Please always use one of our designated genuine
batteries. We cannot guarantee the safety and
performance of our cordless power tool when used with
batteries other than these designated by us, or when the
battery is disassembled and modified (such as
disassembly and replacement of cells or other internal
parts).
GUARANTEE
We guarantee HiKOKI Power Tools in accordance with
statutory/country specific regulation. This guarantee does
not cover defects or damage due to misuse, abuse, or
normal wear and tear. In case of complaint, please send
the Power Tool, undismantled, with the GUARANTEE
CERTIFICATE found at the end of this Handling
instruction, to a HiKOKI Authorized Service Center.
NOTE
Due to HiKOKI's continuing program of research and
development, the specifications herein are subject to
change without prior notice.
TROUBLESHOOTING
The device does not work:
– Check if the plug or battery are inserted until the stop.
– If the current selector switch is in "battery" position:
Check the charge status of the battery charging.
Charge the battery if necessary.
– If the current selector switch is set to 12 V: Switch on
the ignition of your vehicle.
– Is the device switched on from the rotary knob and on
the operating mode switch?
The device does not cool properly:
– Place the device in a cooler location. Do not expose to
direct sunlight.
– Ensure that the ventilation slots are not covered.
Sufficient air circulation must be ensured.
– Increase power: Turn the rotary knob in clockwise
direction.
The device does not warm properly:
– Ensure that the ventilation slots are not covered.
Sufficient air circulation must be ensured.
– Increase power: Turn the rotary knob in clockwise
direction.
10