HIKOKI CG 36DC Instrucciones De Manejo página 15

4. Never operate the machine with damaged guards or
shields or without guards or shields in place.
5. Switch on the motor only when the hands and feet are
away from the cutting means.
6. Always disconnect the machine from the power supply
(i.e. remove the plug from the mains or remove the
disabling device)
○ whenever the machine is left user;
○ before clearing a blockage;
○ before checking, cleaning or working on the machine;
○ after striking a foreign object to inspect the machine for
damage;
○ if the machine starts to vivrate abnormally, for
immediately check.
7. Take care against injury to feet and hands from the
cutting means.
8. Always ensure that the ventilation openings are kept
clear of debris.
9. Never modify the unit/machine in any way. Do not use
your unit/machine for any job except that for which it is
intended.
10. If the unit striking a hard object or there appears to be
excessive vibration, inspect it carefully to check there is
no damage, cracks or deformation.
Using a tool that is damaged, cracked or deformed
could result in injury.
11. The guard extension is equipped with the knife.
Never place your hands near the knife.
12. Do not wear multiple belt harnesses or multiple
shoulder harnesses at the same time.
When wearing the shoulder belt, make sure that other
attachments do not interfere with the quick release
bracket of the shoulder belt.
13. When operation is prolonged, take a break periodically
so that you may avoid possible Hand-Arm Vibration
Syndrome (HAVS) which is caused by vibration.
● Maintenance, transport and storage
1. Disconnect the machine from the power supply (i.e.
remove the plug from the mains or remove the disabling
device) before carrying out maintenance or cleaning
work.
2. Use only the manufacturer's recommended
replacement parts and accessories.
3. Inspect and maintain the machine regularly. Have the
machine repaired only by an authorized repairer.
4. When not in use, store the machine out of the reach of
children.
5. Clean and maintain the unit carefully and store it in a dry
place.
6. When transporting in a vehicle or storage, cover blade
with blade cover.
7. When cutting edges become dull, re-sharpen or file as
shown in the illustration or contact a HiKOKI Authorized
Service Center. Incorrect sharpening may cause
excessive vibration.
● KICKBACK DANGER (Fig. 3)
When using metal cutting attachments such as blades,
contact with obstacles such as trees or other hard surfaces
with the front or right portion of the spinning attachment
may force the unit to catch on an obstacle, resulting in a
kickback reaction towards the right side of the operator.
Kickback may occur when the cutting attachment comes
into contact with tree stumps or rocks hidden behind
weeds. Always make sure there are no obstacles hidden by
weeds before starting work.
To minimize the danger of kickbacks when they do occur,
always position the unit to the right side of the body during
operation. With the operator properly positioned as the
cutting attachment rotates, this will reduce the danger of the
unit's direct contact with the body.
PRECAUTIONS FOR CORDLESS
GRASS TRIMMER / BRUSH CUTTER
WARNING
1. Exercise patience in all work with the tool. And dress
properly to keep warm.
2. Plan all work ahead to prevent accidents.
3. Do not operate the tool at night or under bad weather
conditions when visibility is poor. And do not operate
the tool when it is raining or right after it has been
raining.
Working on slippery ground could lead to an accident if
you lose your balance.
4. Inspect the cutting attachment before starting work.
Do not use the tool if the cutting attachment is cracked,
scarred or bent.
Make sure the cutting attachment is properly attached.
A cutting attachment that falls apart or comes loose
during operation could cause an accident.
5. Be sure to attach the guard before starting work.
Operating the tool without this parts could lead to injury.
6. Be sure to attach the handle before starting work. Make
sure it is not loose but properly attached before starting
work. Hold the handle firmly during work and do not
swing the tool around, but use the correct posture and
maintain your balance.
Losing your balance during work could lead to an injury.
7. Take care when starting the motor.
Place the tool on level ground.
Do not operate the tool within 15 m of people or
animals. Make sure that the cutting attachment does
not come into contact with the ground or trees and
plants.
A careless start could lead to injury.
8. Do not secure the lock lever.
Accidentally pulling back the lever could lead to
unexpected injury.
9. Before leaving the tool, press the power switch to turn it
off.
10. Operate the tool with care near electric cables, gas
pipes and similar installations.
11. Look out for and remove empty cans, wire, stones or
other obstacles before starting work. And do not work
near tree roots or rocks.
Working in such areas could damage the cutting
attachment or lead to injury.
12. Never touch the cutting attachment during operation.
Also make sure it does not come into contact with your
hair, clothes, etc.
13. In the following situations, turn off the motor and check
that the cutting attachment has stopped rotating.
To move to another work area.
To remove rubbish or grass that has become stuck in
the tool.
To remove from the work area obstacles or the rubbish,
grass and chips generated by trimming.
To lay down the tool.
Doing this with the cutting attachment still rotating could
lead to unexpected accidents.
14. Do not use the tool within 15 m of another person.
When you work with someone else, maintain a distance
of more than 15 m.
Flying chips could lead to unexpected accidents.
When working on unstable surfaces like slopes, make
sure that your co-worker is not exposed to any hazards.
Use whistles or other means for calling the attention of
your co-workers.
15. When grass and other objects become entangled in the
cutting attachment, turn off the motor and make sure
the cutting attachment has stopped rotating before
removing them.
15
English