Sears Kenmore PG-40407S0LF Manual Del Usuario página 10

WARNING
Turn controls and gas source or tank OFF when not
in use.
CAUTION
If ignition does NOT occur in 5 seconds, turn the
burner controls OFF, wait 5 minutes and repeat the
lighting procedure. If the burner does not ignite with
The valve open, gas will continue to flow out of the
burner and could accidently ignite with risk of injury
Match Lighting
▲Do not lean over grill while lighting.
1. Open lid during lighting.
2. Place match into match holder (hanging on left side panel).
Light match, and insert match holder through lighting hole on left
side of firebox. Align lit match with first burner on left.
3. Turn knob of first burner on left to HI position. Be sure burner
lights and remains lit. Withdraw match holder from
firebox and extinguish match if still lit.
4. To light other burners, turn each knob in succession to HI.
4. To light other burners, turn each knob in succession to HI.
5. Once burners are lit, adjust knobs to desired flame setting.
5. Once burners are lit, adjust knobs to desired flame setting.
Sideburner Match Lighting
1. Open sideburner lid. Turn on gas at LP cylinder.
2. Place lit match near burner.
3. Turn sideburner knob to HI. Be sure burner lights and stays lit
Burner Flame Check
• Remove cooking grates and flame tamers. Light burners, rotate
knobs from HIGH to LOW. You should see a smaller flame in
LOW position than seen on HI. Always check flame prior to
each use. If only low flame is seen refer to "Sudden drop or low
flame" in the Troubleshooting Section.
Turning Grill Off
• Turn all knobs to OFF position. Turn LP cylinder off by turning
Ignitor Check
• Turn gas off at LP cylinder. Press and hold electronic ignitor button.
"Clicking" should be heard and spark seen each time between
collector box or burner and electrode. See "Troubleshooting" if no
click or spark.
Valve Check
• Important: Make sure gas is off at LP cylinder before checking valves.
Knobs lock in OFF position. To check valves, first push in knobs and
release, knobs should spring back. If knobs do not spring back, replace
valve assembly before using grill. Turn knobs to LOW position then turn
back to OFF position. Valves should turn smoothly.
Hose Check
• Before each use, check to see if hoses are cut or worn. Replace
damaged hoses before using grill. Use only valve/hose/regulator as
specified in the parts list of this Use & Care Guide.
Cast Iron Grate Seasoning (if applicable)
First Use – Before first use, season cast iron grates as follows:
Rinse cast iron grates with hot water. Do not use soap. Dry grates
thoroughly with a cloth towel. Coat grates with vegetable oil
or non-stick cooking spray. Place grates in grill. Start grill and
slowly raise temperature to 350° - 400° F. Heat grates for one
hour. Turn off grill and allow grates to cool completely before
using to cook.
Cleaning – Do not use soap when cleaning grates. Clean grates
with a stiff brush and hot water. Dry grates thoroughly with
cloth towel.
Re-seasoning – Re-season grates when rust spots appear on
grate surface. When re-seasoning grates, soap may be used
with hot water to clean grates. After cleaning, dry grates
thoroughly with a cloth towel. Coat grates with vegetable oil
or non-stick cooking spray. Place grates in grill. Start grill and
slowly raise temperature to 350° - 400° F. Heat grates for one .
hour. Turn off grill and allow grates to cool completely before
using again.
General Grill Cleaning
• Do not mistake brown or black accumulation of drip and smoke for
paint. Interiors of gas grills are not painted at the factory (and
should never be painted). Apply a strong solution of detergent and
water or use a grill cleaner with scrub brush on insides of grill lid and
bottom. Rinse and allow to completely air dry. Do not apply a
caustic grill/oven cleaner to painted surfaces.
• Porcelain surfaces: Because of glass-like composition, most residue
can be wiped away with baking soda/water solution or specially
formulated cleaner. Use nonabrasive scouring
stains.
HI
LO
powder for stubborn
146.47223610 • 9