Publicidad
Idiomas disponibles
Idiomas disponibles
3. Insert the screws into the holes and tighten
the screws until only 6.5mm of the screws
are exposed.
OR
4. Place the baby unit on the wall
mount bracket, and then slide it
forward until it locks into place.
Align the holes on the wall mount
bracket with the screws on the
wall, and slide the wall mount
bracket down until it locks into
place.
5. You can maximize your baby unit's viewing angles by tilting the wall mount bracket.
Hold the baby unit, and then rotate the knob in anticlockwise direction. This will loosen
the joint of the wall mount bracket.
Tilt your baby unit up or down to adjust to your preferred angle. Then, rotate the knob
in clockwise direction to tighten the joint and secure the angle.
1
2
20
Frequently asked questions
Below are the questions most frequently asked about the baby monitor.
Why does the
Try the following (in the order listed) for common cure:
baby monitor
1. Disconnect the power to the baby unit and the parent unit.
not respond
2. Wait a few seconds before connecting power back to the baby unit and the
normally?
parent unit.
3. Turn on the baby unit and the parent unit.
4. Wait for the parent unit to synchronise with the baby unit. Allow up to one
minute for this to take place.
Why doesn't the baby
Perhaps the parent unit is not connected to the power. Insert the adaptorplug into
unit and parent unit
the parent unit and insert the adaptor in a wall socket. Then, press
power-on light illumi-
switch on the parent unit and to establish connection with the baby unit.
nate when the units are
Perhaps the baby unit is not connected to the power. Insert the adaptor plug into
switched on?
the baby unit and insert the adaptor in a wall socket. Then, slide the
switch to ON to switch on the baby unit to establish connection with the parent unit.
Why doesn't my parent
Make sure the power is not controlled by a electronic wall switch.
unit charge while con-
The battery may de degraded through extended use or defective. See Warranty
nected to AC power?
for repair/replacement.
Why is my screen in
The screen is in black and white during night-time or in a dark room when the night
black and white?
vision feature is activated. This is normal.
Why do I get glare or
During night-time or in a dark room, the surroundings and other interfering factors,
blurry display on my
like lighting, objects, colours and backgrounds may affect the image quality on your
screen when viewing my
parent unit screen. Adjust the baby unit angle or place the baby unit at a higher
baby at night?
level to prevent glare and a blurry display.
Why does the baby
The parent unit and baby unit may be too close to each other.
monitor produce a
• Move the parent unit away from the baby unit until the noise stops; OR
feedback noise?
• Turn down the volume of your parent unit.
Why does the parent
The baby unit(s) may be out of range. Move the parent unit closer to the baby unit
unit beep?
(but not less than 1m).
The parent unit may not have enough charge for the parent unit to perform normal-
ly. Charge the battery in the parent unit until the battery icon becomes solid
The temperature of your baby's room may be too high or too low.
Why does the parent
The baby unit also picks up other sounds than those of your baby. Adjust the VOX
unit react too quickly to
sensitivity level to a lower level or lower the parent unit speaker volume.
other sounds?
Why don't I hear a
The parent unit speaker volume may be too low. See Adjust parent unit speaker
sound/Why can't I hear
volume to increase the volume.
my baby cry?
Why can't I establish a
The baby unit may be out of range. Move the parent unit closer to the baby unit
connection? Why is the
(but not less than 1m).
connection lost every now
Other electronic products and wireless products may cause interference with your
and then? Why are there
baby monitor. Try installing your baby monitor as far away from these devices as
sound interruptions?
possible.
Power to
ON/OFF
21
.
Publicidad
