Publicidad
Idiomas disponibles
Idiomas disponibles
System Setup
Saturation
Enter the【Saturation】option, press【►】key to
enter the sub-menu, then use the direction keys
"Up" or "Down" to adjust saturation parameters.
SHARPNESS
Sharpness
Enter the【Sharpness】option, press 【►】key to
enter the sub-menu, then use the direction keys
"Up" or "Down" to adjust sharpness parameters.
SHARPNESS
Dynamic Range
Dynamic Range
Enter the【
】 option, press
【►】 key to enter the the sub-menu then use the
direction keys "Up" and "Down" to select your
required option.
Dual Mono
Enter the【Dual Mono】 option, then press【►】
key to enter the sub-menu; there are four modes to
choose from: STEREO/MONO L/ MONO R/ MIX
MONO.
11
Bluetooth Operation/USB Copy
Bluetooth Reception
To connect an external device to this unit via
Bluetooth:
1. Press "Function Switch" on the remote control or
on the panel to select the Bluetooth function. The
corresponding screen will then display "BT"
indicating that the Bluetooth function is on.
2. Ensure the Bluetooth function is on on the
external device and search for GEMINI GVD-2800.
Once found, click on it and pair. Some devices
may need a pin code to connect; try 0000 or 1234.
Once connected, you will hear a signal indicating
that the connection is successful.
USB COPY
CD File Copy
When playing CD disc, press 【Copy】 key on the
remote, and enter the copy operation interface.
Multiple Setup
1. Move the highlight bar to the "SPEED" option,
press the 【ENTER】 key, then select the
desired multiple (i.e. copy speed).
2. In the copying process, select "CHANGE SPEED"
option or press 【ENTER】 key to switch the copy
speed.
Bit Rate Setup
Move the highlight bar to the "
BITRATE
" option and
press
to set up; for the file with high bit
【ENTER】
rate, the capacity will be enlarged and the quality of
file will be closer to that of original file. The system
default is: 128
KBPS
.
Create ID3 Information
Move the highlight bar to "CREATE ID3 TAG"
option, press 【ENTER】 key to select or cancel.
B y s e l e c t i n g t h i s o p t i o n d u r i n g t h e c o p y i n g
p r o c e s s , t h e fi l e w i l l b e c r e a t e d w i t h I D 3
information which is produced automatically by the
system.
Create File List
Move the highlight bar to "CREATE FILE LIST"
option, then press 【ENTER】 key to select or
cancel. By selecting this option during the copying
process, a file list will be produced automatically.
Create Playlist
Move the highlight bar to "TRACK" option, press
r i g h t k e y t o s e l e c t t r a c k o p t i o n t h e n p r e s s
【ENTER】key to select the song to be copied or to
be cancelled.
Copy
Move the highlight bar to "START" option; at this
time, the information about this copy will be shown
on the right hand side (TOTAL TRACKS, TOTAL
TIME and TOTAL SIZE). Then press 【ENTER】
key to start copying and system will write the CD in
M P3 format onto the designated U S B. When
copying at normal speed, you can listen to the
content to be copied at the same time; when
selecting 4 times speed, it will be mute. Please
note: When you press the 【ENTER】 key to switch
speed, there will be slight sound which continues
for a few seconds.
Return from Copying Screen
Move the highlight bar to "QUIT" option and press
【ENTER】key to confirm QUIT.
P l e a s e n o t e : D u r i n g c o p y, e n s u r e t h a t t h e
available space on the USB is enough for the size
of the file(s) to be copied then insert the USB into
the USB interface. If you have two tracks with the
same title, rename one of the tracks, otherwise
one track will be saved over the other. While
copying, do not pull the USB out or shut the unit
down, as this could damage the unit or USB. If the
USB cannot be read after it has been copied,
please format the USB on your computer.Before
you format, please save the important data from
the USB.
12
Publicidad
