WERKU WK401620 Instrucciones Originales página 4

DESCRIPTION OF THE PRODUCT.
The cordless grinder has been designed to carry
►
out jobs of grinding and cutting
to familiarize yourself with the cordless grinder
before use.
3
6
4
5
1. Switch.
2. Safety switch.
3. Block button.
4. Axis.
5. Disc protector.
6. Auxiliary handle.
7. Battery.
USE INSTRUCTIONS.
Before starting the cordless grinder, we
►
recommend that you carefully read all of the
instructions as indicated
regulations regarding the prevention of accidents,
health and safety directives, laws and applicable
restrictions for work places
must only be used by persons who have been
instructed in its use and only for the purposes for
which it has been designed.
POWER SUPPLY.
Make sure the power supply is adapted to the
►
requirements shown on the information panel of
the cordless grinder (1)
voltage will make it operate slowly
performance and may cause the motor to overheat.
BATTERY AND CHARGER.
If the battery housing is damaged, do not insert
►
it in the charger, as there may be a risk of electric
shock The charger and battery are designed to
►
work together, do not attempt to charge the battery
with any other model of charger
the charger to damp conditions
is designed for use with rechargeable batteries,
any other type of use may pose a fire risk or
cause electric shocks
from sources of heat
►
incorrect reassembly may increase the risk of fire,
explosion or electric shocks
to enter the charger, as they may cause electric
shocks Do not store the charger or the batteries
►
in temperatures higher than 40ºC
charger at a different voltage to that specified by the
Refer to this plan
►
1
Please respect all
►
The cordless grinder
►
Using the motor at low
►
This will reduce
►
Do not expose
►
The charger
►
Keep the charger away
►
Do not open the charger,
Do not allow liquids
►
Never use the
►
manufacturer
under any circumstances
batteries, even when they are empty or broken, as
they may explode
air temperatures any lower than 4.5ºC or higher than
40.5ºC to prevent damage
battery may heat up during the charging process,
this is normal, and does not mean there is a problem
2
The battery must be recharged when it does
►
7
not produce enough energy in situations when
it previously did, do not use the battery in these
conditions
►
when it does not have a battery inserted.
BATTERY INSTALL.
To remove the battery hold the cordless grinder
►
firmly by the handle, press the battery catch and
remove it (2).
CHARGING BATTERY.
Insert the charger jack into the socket on the
►
battery Connect the charger to the power supply
►
It will take between 2.5 and 3 hours to charge
►
the battery fully at 20ºC
as a result of direct sunlight or other factors, the
pilot light may not illuminate
the battery to cool and then restart the charging
process Disconnect the charger from the power
►
supply Hold the charger firmly and pull the
►
battery out, putting it away in a suitable place
Due to their internal chemical composition,
►
batteries that have never been used or left unused
for long periods of time may not produce their full
output during their first or second use
temporary phenomenon, to restore the optimal
battery activity, repeat this process three times
with each of them.
DISC ASSEMBLY.
Unplug the battery first
►
(3) Warning! Only press the block button when
►
the disc is completely still
only be used for mounting and dismounting of the
grinding discs
with the provided accessory (4)
the working surface facing outwards (5)
tighten the nut with the hand over installed disc (6).
PREPARATION.
Verify that the disc diameter has the correct
►
measure Before operating the cordless grinder,
►
check if the disc is well tightened (7)
the guard should be properly mounted and fixed
(8) Turn the spindle and check it manually for
►
any faults (9).
4
English
The batteries must not be opened
►
Do not attempt to burn
►
Do not charge the batteries in
►
Both the charger and
►
Disconnect the charger from the mains
If the battery overheats
►
In this case, leave
►
Press the block button
►
The block button should
►
Loosen the disc tightening bolt using
►
Fit the disc with
►
This is a
►
To slightly
►
Make sure
►