VONROC RT501AC Traducción Del Manual Original página 12

EN
Wear protective gloves to reduce the risk of
injury posed by handling sharp router bits and/
or rough workpieces with sharp edges. Wear a
face visor or safety goggles to reduce the risk
of eye injury due to flying parts.
- Always connect the router table to a dust
extraction system according to the instructions
contained in this user manual. Be aware that
toxic dust can be produced when routing wood.
- Never use router bits or other tools, which are
not designed for use with the router table and/
or recommended for use with the router table
by the manufacturer. A loss of control can lead
to injury. Use only router bits which are marked
for manual feed (MAN) according to EN 847-1.
- Read, understand and follow all safety instruc-
tions printed on the router table.
- Hand/finger contact with the rotating router
bit can cause serious injury. Ensure that the
spindle guard is installed and in good working
order as described in this user manual as this
reduces the risk of contact with the rotating
router bit. Ensure that the router bit has come
to a complete stop and disconnect the machine
from the mains before carrying out any kind of
maintenance or adjustments.
- Always use the feather boards provided, espe-
cially when working with thinner workpieces.
This reduces the risk of 'kickback,' a sudden
reaction caused by the loss of control over a
smaller workpiece.
- When working with longer workpieces always
use the side tables provided and an additional
roller stand if necessary to prevent the risk of
the workpieces tipping over in an uncontrolled
way as this could lead to a dangerous situation.
- Incorrect use of router bits, workpieces and
workpiece feed devices can lead to dangerous
situations. Read the appropriate instructions
contained within this user manual and ensure
that these instructions are provided to any
person who uses the machine.
- Improper maintenance of the router can lead
to uncontrollable situations. Use only sharp,
well-maintained router bits and adjust these
according to the instructions provided by the
manufacturer. Router bits may only be used
for the purpose for which they were intended.
Always use the appropriate router bit for your
application and ensure that it is in good condi-
tion as this reduces the risk of accidents.
12
- Accidental contact with the router table's
moving parts can lead to dangerous situations
and/or accidents. Switch the machine off and
disconnect it from the mains when it is not in
use, before you perform any maintenance and
before you change or adjust the router bit. This
precautionary measure prevents the tool from
being started accidentally.
- Incorrect use of fences and other workpiece
feed devices can lead to dangerous situations.
Consult the instructions in the appropriate part
of this user manual.
- Incorrect positioning, fitting or fastening of the
router bit can lead to dangerous situations. Be
sure that the router bit rotates in the correct
direction and that the workpiece is fed into the
spindle against the direction of rotation of the bit.
- Be sure to select the correct router bit speed for
your application. Consult the manual supplied
with your electric router for this purpose.
- Keep your hands away from the workpiece by
using a fence, push stick or other feed device to
feed the workpiece towards the router bit. Use
the feather boards supplied to hold the work-
piece instead. This reduces the risk of injury.
- Ensure that the router table is located on a
stable, level surface.
- Keep your workplace tidy and remove chips and
dust regularly. Clean your power tool's ventila-
tion slots regularly.
Electrical safety
Always check that the voltage of the power
supply corresponds to the voltage on the
rating plate.
• Do not use the machine if the mains cable or
the mains plug is damaged.
• Only use extension cables that are suitable
for the power rating of the machine with a
minimum thickness of 1.5 mm
tension cable reel, always fully unroll the cable.
2. MACHINE INFORMATION
Intended use
The router table is exclusively designed for private
use and for hobby and DIY projects for routing in
wood in conjunction with an electric router. Any
other applications are expressly prohibited and are
deemed improper use.
. If you use a ex-
2
WWW.VONROC.COM