Publicidad
Idiomas disponibles
Idiomas disponibles
ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
Always lock the trigger or remove
WARNING
the battery pack any time the tool
is not in use.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
Only use accessories specifically
WARNING
recommended for this tool. Others
may be hazardous.
To reduce the risk of injury, always wear proper
eye protection marked to comply with ANSI Z87.1.
Changing the Cutting Wheel
Replace the cutting wheel when it becomes dull or
damaged.
1. Insert the battery pack.
2. Press the Mode button
modes until the carriage opening mode indicator
is lit. Squeeze and hold the trigger to line up
the carriage.
3. WARNING! Remove battery to avoid starting the tool.
4. Remove the clip ring.
5. Slide out the wheel axle.
6. Remove the cutting wheel.
7. Insert the new cutting wheel.
8. Align all spring, jaw, and cutting wheel holes.
9. Slide the wheel axle through the spring, jaw, and
cutting wheel, and hold it in with your index finger.
10. Replace the clip ring.
Jaw
OPERATION
To reduce the risk of injury, always
WARNING
wear proper eye protection marked
to comply with ANSI Z87.1.
When working in dusty situations, wear appro-
priate respiratory protection or use an OSHA
compliant dust extraction solution
Fuel Gauge
To determine the amount of charge left in the battery,
turn the tool ON. The fuel gauge will light up for 2-3
seconds. When less than 10% of charge is left, 1
light on the fuel gauge will flash 4 times.
To signal the end of charge, 1 light on the fuel gauge
will flash 8 times and the tool will not run in cutting
mode. The tool can temporarily run in carriage open-
ing mode to return the carriage to its open position.
Charge the battery pack.
to cycle through the
Spring
Clip ring
Wheel axle
Cutting wheel
If the battery becomes too hot, the fuel gauge lights
will flash and the tool will not run. Allow the battery
to cool down.
The sight-line window has an LED to allow for better
accuracy in dark areas. The LED will remain lit for a
few minutes after the tool is turned on, the trigger is
pulled, or the Mode button
is pressed.
Using the Control Panel
The control panel can be set to three modes: car-
riage open, cutting, and lock. Always allow the motor
to come to a complete stop before using the control
switch.
1. To insert or remove tubing, press the mode button
to cycle through the modes. When the carriage
opening mode indicator
hold the trigger to line up the carriage. The car-
riage will return to the open position and the jaws
will unlock from the workpiece.
2. To cut, press the mode button
the modes until the cutting mode indicator
lit. See "Cutting".
3. To lock or unlock the tool, hold the mode
for two seconds. The lock indicator
when the tool locks.
Lock indicator
Carriage
opening
mode
indicator
To reduce the risk of injury, wear
WARNING
gloves when cutting. Cut tubing
can be sharp. Do not hold end of tubing. Cutter
will rotate tubing when trigger is pulled creating
a laceration hazard.
Keep hands away from all cutting edges
and moving parts. Fingers can be pulled
into cutting carriage and be cut or
crushed.
Do not cut off pieces of tubing less than
NOTICE
1/2" long. Small pieces can be pulled
into moving carriage and damage tool.
The tubing cutter can cut copper tubing from 1-1/4"
to 2" (trade size). Always support the workpiece to
prevent rotating and moving during cutting.
1. Press the mode button
modes until the carriage opening mode indicator
is lit.
2. Squeeze and hold the trigger to line up the car-
riage.
NOTE: If the cutting carriage has locked in place
and will not move freely in carriage open position,
run the tool in cutting mode for several seconds,
then run in carriage opening mode again to line
up the cutting carriage.
4
LED
on the control panel
is lit, squeeze and
to cycle through
Mode
button
Cutting
mode
indicator
Cutting
to cycle through the
is
button
will light
Publicidad
