Publicidad
Idiomas disponibles
Idiomas disponibles
EN - USER MANUAL
• 7 programmable buttons
• Hot swappable mechanical switches
• Top grade optical sensor with up to 26000 DPI
• Advanced software with macro/profile editor
• 4 sets if spacers for button stroke adjustment
• Dual communication mode (2.4GHz | USB)
• 2 changeable back covers for body size adjustment
• Built-in rechargeable battery
INSTALLATION
• Connect the cable to a free USB port on your computer, it is necessary to wait about
15 seconds for the first connection until the drivers are fully installed.
• The mouse includes software that allows you to set up advanced features, if you
want to use these features, you need to download and install the software from our
website www.genesis-zone.com
• Open the installation folder and then double-click the setup.exe file.
• Follow the instruction to install the program.
• After a successful installation, the software icon appears on the main bottom panel.
Double-clicking the icon opens the settings interface.
WIRED MODE
The mouse will switch to wired mode automatically once you connect USB cable to the
mouse and computer.
Tips:
• Wired mode offers better smoothness performance of sensor than wireless mode,
for best results set the polling rate to 1000 Hz.
• Wired mode allows simultaneous using of the mouse and charging the battery.
WIRELESS MODE
Connection of mouse via USB receiver
• Turn ON your computer or other compatible device
• Move the switch located on the bottom of the mouse to
• Connect receiver to a free USB port on your computer
• The operating system will automatically install the required drivers
• The mouse is ready for use
Note:
• The device is equipped with intelligent technology for energy management. When
the mouse enter into hibernation (sleep) mode, press any button of the mouse for
its revival.
• The mouse is equipped with an ON/OFF switch to save the battery power when not
in use for longer period.
Tips:
• To get the best performance of wireless connection and reduce latency, connect
the USB receiver as close as possible to the mouse and make sure that there are no
4
|
position
obstacles between the mouse and the receiver that can interfere with the wireless
signal.
• In wireless mode set the polling rate to 500 Hz to get better smoothness
performance of sensor.
CHARGING THE BATTERY
• Connect the included USB-C cable to the mouse
• Connect USB plug to a suitable power source (max. output DC 5V 0,5A)
• When the battery is fully charged, the DPI indicators will stop moving.
Note: When the battery level is too low, the DPI indicator will starts flashing.
Caution: Please charge the battery every 3 months, if you do not use the mouse for a
long time. Long-term storage of the mouse with low battery level, or using the chargers
with power over 5V 0,5A may damage the battery.
OPENING THE MOUSE
• Remove the back cover by pulling at place 1 shown on illustration
• Push the button cover at place 2 shown on illustration and pull to remove it. We
recommend to remove USB receiver beforehand to make it easier of removing the
cover.
• Slide the locking mechanism 3 located on the bottom of mouse and place opening
tool 4 at the location 5 shown on illustration to open the mouse body
REPLACING THE SWITCHES
• To replace the switches simply remove the switch 6 shown on illustration after
opening the mouse body and insert the new one in the right direction
BUTTON TRAVEL DISTANCE ADJUSTMENT
• Factory pre-installed button spacers are 0,6 mm
• If you want adjust button travel distance remove pre-installed spacers from part 7
and insert new spacers with selected thickness
BUTTON FORCE ADJUSTMENT
• Factory pre-installed button springs are 15 g (silver color spring)
• If you want apply a higher button force, remove pre-installed springs from part 8
and insert new springs with 25 g force (copper-colored spring)
CLOSING THE MOUSE
• Insert the button cover into dedicated place starting from the front and push the
part 9 shown on illustration to snap into latches
• Close the mouse body by sliding the front part 10 forward firstly, then slide the
locking mechanism 3 and push the back part firmly to snap into the latches
• Insert the back cover into dedicated place by first inserting the front part into
mounting holes 11
FR - MANUEL DE L'UTILISATEUR
• 7 boutons programmables
• Microcommutateurs mécaniques remplaçables
• Capteur optique supérieur à une résolution de 26000 DPI
• Logiciel avancé avec éditeur de macros/profils
|
5
Publicidad
