Mitsubishi Electric Mr.Slim PEAD-A09AA9 Manual De Instalación página 21

8. Electrical work
Function table 1
Select unit number 00
Mode
Power failure automatic recovery *1*2
(AUTO RESTART FUNCTION)
Indoor temperature detecting
LOSSNAY connectivity
Power voltage
Auto mode
Function table 2
Select unit numbers 01 to 04 or all units (AL [wired remote controller]/07 [wireless remote controller])
Mode
Filter sign
External static pressure
*1 When the power supply returns, the air conditioner will start 3 minutes or 1 minute later (hinge on Outdoor unit).
*2 Power failure automatic recovery initial setting depends on the connecting outdoor unit.
Note: When the function of an indoor unit were changed by function selection after the end of installation, always indicate the contents by entering a
appropriate check field of the tables.
8.5. CN24 settings (Mass save settings)
[Fig. 8-5-1] (P.10)
• Heat Pump auto ON/OFF setting depend on Outdoor temperature
• Heater via CN24 auto ON/OFF setting depend on Outdoor temperature or difference
between setting temp. and indoor ambient temperature.
1
• Select "Service" from the Main menu, and press the [SELECT/HOLD] button.
• Select "Settings" with the [F1] or [F2] button, and press the [SELECT/HOLD]
button.
2
• Select "CN24 settings" with the [F1] or [F2] button, and press the [SELECT/
HOLD] button.
Connected outdoor unit
PUZ-A**
PUZ-HA**
SUZ-KA09/12/15/18/24/30/36NA2
SUZ-KA09/12/15/18/24/30/36NAHZ
MXZ
* If outdoor unit not listed above table, please refer to outdoor IM for details.
8.6. CNUS wiring (accessory)
Connectors are color coded as shown in the table below. Be sure to connect the right-colored connectors.
Connector
CNF (HUMIDITY INPUT)
CNER (ERV INPUT)
CN2C (ERV OUTPUT)
CN24-2 (HEATER CONTROL 2ND)
Settings
Not available
Available
Indoor unit operating average
Set by indoor unit's remote controller
Remote controller's internal sensor
Not Supported
Supported (indoor unit is not equipped with outdoor-air intake)
Supported (indoor unit is equipped with outdoor-air intake)
230V
208V
Energy saving cycle automatically enabled
Energy saving cycle automatically disabled
Settings
100 Hr
2500 Hr
No filter sign indicator
External static pressure
35 Pa [0.14 in. WG]
50 Pa [0.20 in. WG] (before shipment)
70 Pa [0.28 in. WG]
100 Pa [0.40 in. WG]
150 Pa [0.60 in. WG]
UB
Setting range Default Setting range
32 °F 70 °F 47 °F 23 °F
~
32 °F 70 °F 47 °F 23 °F
~
32 °F 70 °F 47 °F 23 °F
~
32 °F 70 °F 47 °F 23 °F
~
32 °F 70 °F 47 °F 23 °F
~
Wiring color Dummy connector
GREEN GREEN
RED RED
BLACK BLACK
BLUE BLUE
Mode no.
01
02
03
04
05
Mode no.
07
Setting no. of Setting no. of
mode no. 08 mode no. 10
08
2 1
3 1
1 2
2 2 10
3 2
3
• Set the indoor unit refrigerant address with the [F1] or [F2] button, then press
the [SELECT/HOLD] button.
4
• Select "Limit settings" or "CN24 enabled condition" with the [F1] or [F2] button,
and press the [SELECT/HOLD] button.
5
• Set UB, UA, LB, LA with [F3] or [F4] button and then press the [SELECT/HOLD]
button.
6
• Set T (difference between ambient temp. and setting temp.) with [F3] or [F4]
button and press the [SELECT/HOLD] button.
UA
Default Setting range
61 °F 38 °F -27 °F 52 °F
~ ~
61 °F 38 °F -27 °F 52 °F
~ ~
61 °F 38 °F 14 °F 52 °F
~ ~
61 °F 38 °F 14 °F 52 °F
~ ~
61 °F 38 °F 14 °F 52 °F
~ ~
Setting no. Initial setting
1
2
1
2
3
1
2
3
1
2
1
2
Setting no. Initial setting
1
2
3
1
2
3
1
2
3
or other mark in the
LB LA
Default Setting range
– -36 °F 43 °F
~
– -36 °F 43 °F
~
– 5 °F 43 °F
~
– 5 °F 43 °F
~
– 5 °F 43 °F
~
Check
Check
Default
–
–
–
–
–
21