Wahl 4550 Manual De Uso página 14

E N G L I S H
Product description
Description of parts (Fig. 1)
A Air outlet
B Release button
C On/off switch, fan settings
D Air inlet
E Hanging loop
F Mains cable
de
G Round thermal brush Ø25 mm for small waves
H Round thermal brush Ø30 mm with extendable bristles for
medium waves
I Round thermal brush Ø38 mm for volume and large waves
en
Technical data
Operating voltage:
fr
Power consumption:
Dimensions (Ø x L):
Weight:
Operating conditions
it
Ambient temperature:
The hot air brush is safety insulated and radio screened. It
meets the requirements of EU Electromagnetic Compatibility
es
Directive 2014/30/EU and Machinery Directive 2006/42/EC.
pt
Operation
Preparation
f Check that the contents are complete.
nl
f Check all the parts for possible transport damage.
Safety
Caution! Damage due to incorrect power supply.
da
f Only operate the hot air brush with the voltage
stated on the nameplate.
sv
Operation
1. Insert the mains plug into the socket.
The hot air brush has 3 heat/fan settings. The cold-
no
shot button can also be used to fix the hairstyle.
2. Switch the hot air brush on at the on/off switch.
fi
3. Select the required temperature/fan setting.
0 Off
I
Setting 1, for a gentle airflow with warm air
tr
II Setting 2, for a strong airflow with hotter air
❆ Cold-shot button
pl 4. Using the on/off switch, switch off the hot air brush after
use.
cs
14
All manuals and user guides at all-guidesbox.com
220 – 240 V / 50/60 Hz
900 – 1100 W
45 x 360 mm
240 – 270 g without mains cable
0 °C – +40 °C
5. Disconnect from the mains.
6. Allow the hot air brush to cool down.
Operation
Attaching/removing thermal round brushes
1. Position the thermal round brush and press it towards the
housing (Fig. 4ⓐ). Pay attention to the marking!
2. Turn the thermal round brush in the direction of the arrow
and lock in position (Fig. 5ⓐ).
3. To remove the thermal round brush, press the release but-
ton (Fig. 5ⓑ).
4. Turn the thermal round brush in the direction of the arrow
(Fig. 5ⓒ) and pull it off the housing (Fig. 4ⓑ).
Thermal round brush with extendable bristles
f The bristles are extended by turning the top of the brush in
the direction of the arrow (Fig. 3ⓐ).
f The bristles are retracted by turning the top of the brush in
the opposite direction (Fig. 3ⓑ).
Tips for successful styling
1. Wash and rinse the hair well.
2. Dry the hair with a towel.
3. Brush or comb the hair.
4. Section off individual strands of hair.
5. Thermal round brush (Ø30 mm) with extendable
bristles:
Extend the bristles (Fig. 3ⓐ).
6. Roll the section of hair, starting from the end and working
upwards, around the thermal round brush to form a curl.
7. Switch the hot air brush to setting I or II and wait until the
hair is dry.
f Do not leave the sections of hair on the hot air
brush for more than a few seconds, otherwise
this could damage the hair.
8. Switch on the cold-shot button to set the curl.
9. Thermal round brushes (Ø25 mm and Ø38 mm):
Turn the thermal round brush out of the hair.
Thermal round brush (Ø30 mm) with extendable
bristles:
Retract the bristles (Fig. 3ⓑ) and slide the thermal round
brush out from the side.
10. Repeat on other sections to dry and style.
Overheat protection
1. The hot air brush is fitted with an overheat protection
facility. If the hot air brush overheats, it switches off
completely. Proceed as follows:
2. Switch the hot air brush off at the on/off switch.
3. Disconnect from the mains.