Auto Power-Off Function - Vox MSB50ABK Manual Del Usuario

En
English
Introduction
Thank you for purchasing the VOX MINI SUPERBEETLE AUDIO Bluetooth
Speaker. To help you get the most out of your new instrument, please read
this manual carefully.
Setup
1. Set the amp head on the frame
top of the speaker cabinet.
If the amp head does not seem to
solidly rest on top of the speaker
cabinet when stacked, attach the
included cushions to the bottom of
the amp head (at the position
shown in the illustration), so that it
comes into contact with the
speaker cabinet frame at the top of the
speaker.
2. Plug the speaker cable that's connected
to the speaker cabinet into SPEAKER
OUTPUT jack.
Please make sure the amp is turned
off when you connect the speaker
cabinet.
3. Turn the VOLUME knob on the amp head to the minimum level.
4. Connect the supplied AC adapter to the power cord. Insert the DC plug
end into the DC 19 V jack. Next, plug the power cord into an AC outlet.
Be sure you're using an AC power outlet of the correct voltage for
your unit.
Use only the supplied AC adapter. Using any other AC adapter may
cause malfunctions.
5. Hold down the power button to turn on the amp.

Auto power-off function

The amp has an auto power-off function. The amp automatically turns off if
no sound is output and no knob or button is operated for approximately 1
hour. Once the amp turns off, it does not turn on again when a knob or
button is operated. After the amp turns off, turn it on again.
When the output level is extremely low or there is very little change in
the sound, the amp may treat that as if "no sound is output." In
addition, depending on the settings, connections and environment, the
amp may treat noise as if "sound is being output," even if there is no
audio or guitar input.
The auto power-off function will not operate while the amp is connected
to another device via Bluetooth.
Part Names and Functions
Amp Head Section
Top Panel
3 4
1
2
1. Power button, LED: Hold down this button to turn on or off the amp.
2. BLUETOOTH button, LED: Use when connecting other devices via
Bluetooth (¬ "Connecting a Bluetooth Audio Device"(p.8).)
3. VOLUME knob: Adjusts the volume of the SPEAKER OUTPUT jack and
PHONES jack.
4. SUB-BASS knob: Adjusts the ultra-low-frequency range of the audio
input.
5. BASS knob: Adjusts the low-frequency range of the audio input.
6. MIDDLE knob: Adjusts the mid-frequency range of the audio input.
7. TREBLE knob: Adjusts the high-frequency range of the audio input.
8. AUX IN jack: Connect an audio player to this jack.
9. PHONES jack: Use this jack if you want to use headphones. The output
level is adjusted with the VOLUME knob.
When a plug is connected to this jack, no sound will be output from
the SPEAKER OUTPUT jack.
Rear Panel
10
10. Guitar amp section:  "Connecting a Guitar"(p.8)
11. DC 19 V jack: Connect the included AC adapter here.
12. SPEAKER OUTPUT jack: Connect the speaker cable to this jack. The
minimum speaker's impedance is 4 ohms, and you will get approx. 50
W output with 4 ohms, 25 W with 8 ohms, and 12.5 W with 16 ohms
load. Connect the included speaker cabinet to any of the jack.
Make sure that the impedance of the speaker cabinet is not less
than 4 ohms.
This is BTL (Bridge-Tied-Load) output. This means both tip and
sleeve is the signal line, and sleeve is not grounded. Only use this
jack for connecting speakers to the amp. Connecting anything else
may result in damages to the amp.
The VOX MINI SUPERBEETLE AUDIO has a built-in protection
system that prevents damage should unusual circumstances occur.
If the sound cuts out for a few seconds, don't worry, this is the amp
protecting itself and your speakers. If you find this happens, simply
reduce the volume on the amp slightly.(This protection only occurs
with 16 ohms speakers. 8 ohms and 4 ohms speakers are
unaffected.)
Speaker Cabinet Section
The speaker cabinet of the VOX MINI SUPERBEETLE AUDIO has one
6.5-inch woofer and one 1-inch tweeter, each VOX custom-made. Just plug
into the cabinet and you'll hear what we mean!
7
5 6 7
12
11
8
9