Makita FS4000 Manual De Instrucciones página 6

depth. One full turn of the lock ring equals 2.0 mm change
in depth.
For Model FS4000X, FS4300X, FS6300X (Fig. 2)
The depth can be adjusted by turning the locking sleeve.
Turn it in "A" direction for less depth and in "B" direction
for more depth. One full turn of the locking sleeve equals
1.5 mm change in depth.
For all Models
Adjust the lock ring so that the distance between the tip of
the locator and the screw head is approximately 1 mm as
shown in the figures. Drive a trial screw into your material
or a piece of duplicate material. If the depth is still not
suitable for the screw, continue adjusting until you obtain
the proper depth setting. (Fig. 3 & 4)
Switch action (Fig. 5)
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
"OFF" position when released.
To start the tool, simply pull the switch trigger. Tool speed
is increased by increasing pressure on the switch trigger.
Release the switch trigger to stop.
For continuous operation, pull the switch trigger and then
push in the lock button.
To stop the tool from the locked position, pull the switch
trigger fully, then release it.
NOTE:
• Even with the switch on and motor running, the bit will
not rotate until you fit the point of the bit in the screw
head and apply forward pressure to engage the clutch.
Lighting up the lamps
For Models FS4200, FS4300, FS4300X, FS6200,
FS6300, FS6300R, FS6300X (Fig. 6)
CAUTION:
• Do not look in the light or see the source of light
directly.
To turn on the lamp, pull the trigger. Release the trigger to
turn it off.
NOTE:
• Use a dry cloth to wipe the dirt off the lens of lamp. Be
careful not to scratch the lens of lamp, or it may lower
the illumination.
Reversing switch action (Fig. 7)
CAUTION:
• Always check the direction of rotation before operation.
• Use the reversing switch only after the tool comes to a
complete stop. Changing the direction of rotation
before the tool stops may damage the tool.
This tool has a reversing switch to change the direction of
rotation. Move the reversing switch lever to the
position (A side) for clockwise rotation or the
(B side) for counterclockwise rotation.
Hook (Fig. 8)
The hook is convenient for temporarily hanging the tool.
6
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Installing or removing the bit
For Model FS4000, FS4200, FS4300, FS6200, FS6300,
FS6300R
To remove the bit, first remove the locator by pulling the
lock ring away from the gear housing. (Fig. 9)
Grasp the bit with a pair of pliers and pull the bit out of the
magnetic bit holder. Sometimes, it helps to wiggle the bit
with the pliers as you pull.
To install the bit, push it firmly into the magnetic bit holder.
Then install the locator by pushing it firmly back onto the
gear housing. (Fig. 10)
For Model FS4000X, FS4300X, FS6300X
To remove the bit, first pull the locator out of the locking
sleeve. Then grasp the bit with a pair of pliers and pull the
bit out of the magnetic bit holder. Sometimes, it helps to
wiggle the bit with the pliers as you pull. (Fig. 11)
To install the bit, push it firmly into the magnetic bit holder.
Then install the locator by pushing it firmly back onto the
locking sleeve. (Fig. 12)
Installing removable cord adapter
For Model FS6300R (Fig. 13)
Insert the removable cord adapter as far as it goes so that
the marking
on the side of connecting to power supply cord is aligned
to the marking
adapter on the side of connecting to the tool.
Turn the removable cord adapter clockwise until it is
locked with a lock button. (Fig. 14)
And at this time the marking
removable cord adapter on the side of power supply cord
is aligned to the marking
removable cord adapter on the side of connecting to the
tool. (Fig. 15)
Removing removable cord adapter
(Fig. 16)
Rotate the removable cord adapter counterclockwise until
it stops while pressing the lower part of the lock button.
Then pull the removable cord adapter in that position.
(Fig. 17)
Use of locator holder (Fig. 18)
The locator can be temporarily held on the locator holder
during replacing bit or using without locator. To hold the
locator, position the trapezoidal holes of the locator on the
swells of the locator holder and push it in.
OPERATION (Fig. 19)
position
Fit the screw on the point of the bit and place the point of
the screw on the surface of the workpiece to be fastened.
Apply pressure to the tool and start it. Withdraw the tool
as soon as the clutch cuts in. Then release the switch
trigger.
on an end of the removable cord adapter
on the other end of the removable cord
on an end of the
on the other end of the