Tabla de contenido
Publicidad
DISPLAY DESCRIPTION
4
3
1. ON/OFF BUTTON
2. VACUUM IN CONTAINERS
3. WELDING BAR SEALING
4. LED
USAGE CONDITIONS
Since the machine is purposely projected to vacuum food, it is
not recommended to use it for different aims.
Any improper or different usage makes the warranty not valid
(see warranty conditions on every machine), and it can
damage the inner components by avoiding the correct working
of the machine.
ATTENTION
Read and follow these instructions before using the
machine and keep them with it.
Keep the environment and working place clean and tidy.
Keep children away from the working place where the
machine is placed.
Do not overload the machine and take care of it.
Place the machine on a stable and safe surface. Should it
fall down, it can be seriously damaged.
Do not vacuum pack liquids, nor powders. The lack of
respect for this indication causes unsafe conditions and
the irreparable damage of the machine.
In order to vacuum food with liquid substances, remove
all exceeding liquid and dry the food with a rag before
packing it; alternatively, use a container with the proper
vacuum lid, supplied by the manufacturer.
Before starting, remove all extra material (knives, blades,
tools...) away from the sealing bar.
Any kind of operation, either for cleaning or fitting, must
be done with the machine off and the power wire
unplugged from the socket, in order to avoid any risk of
involuntary start-up of the machine itself. Follow this rule
even when the machine is not working. Check that
tension and frequency correspond to those indicated on
the machine and that the socket is proportioned to the
electricity absorbed by the machine.
Use exclusively original spare parts and accessories.
Do not immerse nor expose the machine to water. It is
an electrical device!
Do not pull the electric wire to remove the plug.
Replacement
of
the
power
replacements must be carried out by specialized staff
exclusively.
USE AND MAINTENANCE INSTRUCTIONS
IMPORTANT
It is recommended that installation and usage of the machine
are carried out by a single user, since the machine is not
projected for a multiple use.
DESCRIPTION
The machine is essentially composed by a main structure,
innerly composed by steel AISI 430. Inside there are the
switchboard
and
the
vacuum
recommended not to intervene on the vacuum working inner
part (just in case of extraordinary maintenance, that must be
1
2
cable
and
all
electric
working
station.
It
is
carried out by the manufacturer).
The sealing bar – to seal the bag at the end of the cycle – is
placed on the external part of the structure, front and below
part of the machine, together with the gasket, which define
the fixed part of the decompression chambers, where the bag
is usually placed to be packed.
The superior part of the decompression chamber is fixed on
the mobile lid connected to the main structure through two
hinges. This system allows to keep the bag blocked for a
proper suction and its following sealing.
WORKING PROCESS
Take the machine out of its package, place it on the
working table and verify its stability.
It is important that all four supports of the machine
adhere to the surface, in order to get the lid closed tight
to the below part of the machine. This way the correct
working of the machine is granted.
It is recommended to keep the machine packaging, in
order to use it again in the future for possible transfers.
Clean the machine carefully before using it. Clean the
external structure with a humid rag first and then with a
dry one; for the display, use a dry rag only.
It is strictly forbidden to use acid or caustic products.
Insert the plug into the socket.
Switch the machine on, by turning the side switch on I
(on model SV- 43 only).
Keep the button ON/OFF (1) pressed for 2 seconds.
The machine is ready to be used with time and sealing
settings used the last time.
USAGE METHODS
VACUUM CYCLE WITH AUTOMATIC CYCLE
By keeping the machine on, move the lid up.
Insert the product inside the bag.
Insert the bag into the decompression chamber with the
opening part in between the two black gaskets.
Check that the inner component of the bag does not
interfere with the sealing bar. Check that the bag is not
broken and placed steady on the sealing top.
LOW DOWN THE LID WITH A MODERATE PRESSURE
ON THE TWO SIDES OR, IF PRESENT, ON THE
CENTRAL HANDLE. KEEP THE LID PRESSED FOR A
FEW SECONDS UNTIL THE AIR STARTS TO BE
SUCKED OUT. THEN, RELEASE THE LID.
The machine will automatically starts its cycle and the
display will show the vacuum level by lightening the LED
lights.
Once the vacuum is over, the sealing will follow
automatically. Once the sealing is over, the pump stops
working and the mobile lid opens automatically.
The machine is now ready to pack the bag.
VACUUM PACKAGING IN CONTAINERS
This usage mode can be used to vacuum liquids into
containers (supplied by the manufacturers and described in
the section "Optional accessories").
By keeping the machine on, open up the mobile lid placed
on the front part of the machine. It is now possible to
vacuum in containers.
Connect the suction pipe for containers to the aspire
device of the machine, placed in between the gaskets
within the below decompression chamber.
Place the food within the container and close it with the
proper lid.
Connect the second end of the suction pipe to the lid of
the vacuum container.
Start the aspiration by pressing the button PUMP (2)
without closing the upper part of the mobile lid.
The display starts to indicate the vacuum level by
lightening the LED.
As the vacuum is over, the machine stops. It is now
possible to disconnect the device on the lid.
The machine is now ready to pack a new bag or a
container.
This usage mode does not activate the sealing bar (since it
does not need to work), by avoiding accidental burns due to
the lid opening.
IMPORTANT
Always use bags suitable to the vacuum packaging. Otherwise
Publicidad
Tabla de contenido
