Table Of Contents - Dremel 3D45 Manual De Instrucciones

mouth. Dremel filament is not suitable for food
or drink preparation and food utensils. Such use
of objects created by Dremel 3D45 may result in
illness or personal injury.
n. Do not use Dremel 3D45 to create objects
intended for chemical storage. Dremel filament
is not suitable for chemical storage. Such use of
objects created by Dremel 3D45 may result in
property damage and personal injury.
o. Do not modify Dremel 3D45 or alter factory
settings. Modifications may result in equipment
and property damage, and personal injury.
p. Do not expose Dremel 3D45 to temperatures
exceeding 70°C (158°F). Dremel 3D45 may
become damaged. Dremel 3D45 is intended to
operate in temperature between 16-29° C
(60 - 85° F).
q. Do not move or bump Dremel 3D45 or the
extruder during operation. The object may build
incorrectly.
r. Do not change filament spool unless the
building process is completed, stopped, or
paused. Changing the filament during building will
cancel the object and may damage the extruder.
s. Do not pull the filament out until instructed
by the touch screen. Doing so may damage the
extruder.
t. Use extra care not to damage the extruder tip
when clearing debris. Dremel 3D45 will not work
properly with damaged extruder tip and will require
replacement.
u. Before every build make sure that the build
platform is covered with Dremel specified glue.
Use of improper glue may result in equipment
damage and poor object build quality.
v. Be aware of your body position when using
hand tools to remove objects from the build
platform. Sudden tool slip and improper body
position during object removal from the build
platform may result in personal injury.
w. Avoid scratching the build platform when
removing objects. Scratches in the build platform
will result in improper object creation.
x. Do not drop the build platform. Tempered glass
plate may break and result in personal injury.
y. Do not remove tempered glass plate from
plastic holder. Contact with tempered glass plate
edge may result in personal injury.
z. Do not twist or bend the build platform while
removing objects. Tempered glass plate may
separate from plastic holder and result in personal
injury.
aa. Dremel is not responsible for structural integrity
or utility of objects created using Dremel
3D45. Structural models created by inexperienced
designers may result in property damage and
personal injury.
SERVICE
a. Always unplug Dremel 3D45 from its power
before performing any service procedures.
Failure to do so may result in personal injury and
equipment damage.
b. Have your Dremel 3D45 serviced only by an
authorized Dremel service centre using only
Dremel replacement parts. This will ensure that
proper operation and safety of Dremel 3D45 is
maintained.
c. Use only Dremel approved components. Use
of components other than genuine Dremel
components may void warranty.
d. Use only Dremel approved filament. Use of
filament other than Dremel
void warranty on extruder.

TABLE OF CONTENTS

General safety warnings ..................................421
Table of contents...............................................422
Used symbols ....................................................423
Information on Intellectual Property ...............423
Functional Description and Specifications ....423
3D45 Resources ................................................424
Glossary of Terms .............................................425
Getting to know your 3D45 ..............................427
Introduction ........................................................429
Kit Contents*......................................................429
Touch Screen .....................................................431
Touch Screen Icons ..........................................436
Initial Setup ........................................................437
Remote 3D Printing via Local Area
Network Connection using Dremel
DigiLab 3D Slicer ..............................................438
Getting Ready to Build .....................................440
Building ..............................................................446
Removing Your Object ......................................449
Using the Camera .............................................450
Best Practices ...................................................450
Maintenance .......................................................451
Maintenance and Service .................................453
Firmware & Open Source Software ................454
Warranty .............................................................455
®
422
approved filament may
®