White Rodgers 80 Serie Manual De Instrucciones página 5

INST INST ALLER/CONFIGURA ALLER/CONFIGURA
INST INSTALLER/CONFIGURA INST ALLER/CONFIGURA ALLER/CONFIGURATION MENU
4) Ener Energ g g g g y Mana Ener Ener Ener y Mana y Mana y Manag g g g g ement R y Mana ement R ement R ement R ement Reco
configured to be non-programmable).
Energy Management Recovery (E) On enables the
thermostat to start heating or cooling early to make the
building temperature reach the program setpoint at the
time you specify. Heating will start 5 minutes early for
every 1° of temperature required to reach setpoint.
Example Example Example Example: If E On is selected and have your heating pro- Example
grammed to 65° at night and 70° at 7 AM. If the building
temperature is 65°, the difference between 65° and 70° is
5°. Allowing 5 minutes per degree, the thermostat set-
point will change to 70° at 6:35 AM. Cooling allows more
time per degree, because it takes longer to reach set
temperature.
5, 6 & 7) Cy Cy Cy Cyc c c c c le R le Ra a a a a te Selection le R le R te Selection te Selection – The factory default settings te Selection
Cy le R te Selection
with SS/HP switch in SS position for Heat is medium
cycle (ME) and Cool is fast cycle (FA). For Heat Pump
(HP), the default setting is fast cycle (FA).
To change cycle rate, press the
Cycle rate differentials for different settings are:
MODE
Heat (SS) 0.4°F
Cool (SS) 1.2°F
Heat Pump (HP) 1.2°F
8) Select Compr Select Compr Select Compr Select Compressor Loc Select Compr essor Lock k k k k out CL OFF or ON essor Loc essor Loc essor Loc
CL ON will cause the thermostat to wait 5 minutes be-
tween cooling cycles. This is intended to help protect the
compressor from short cycling. Some newer compres-
sors already have a time delay built in and do not require
this feature. Your compressor manufacturer can tell you if
the lockout feature is already present in their system.
When the thermostat compressor time delay occurs, it
will flash the setpoint for up to five minutes.
TION MENU TION MENU
TION MENU TION MENU
eco ecov v v v v er er er er ery y y y y : (this step is skipped if eco eco
or key.
Fast Medium Slow
FA ME SL
0.6°F 1.8°F
– 1.7°F
– 1.7°F
out CL OFF or ON out CL OFF or ON out CL OFF or ON out CL OFF or ON – Selecting
9) System Mode Configur System Mode Configur System Mode Configur System Mode Configura a a a a tion System Mode Configur
configured for Heat and Cool with Auto changeover
(SYSTEM switch with Cool Off Heat Auto) default. It can
also be configured for Heat and Cool (Cool Off Heat),
Heat only with fan (Off Heat), Heat only without fan,
Auto only (Auto Off), and Cool only (Cool Off).
10)Select Bac Select Backlight Displa Select Bac Select Bac Select Bac klight Display y y y y – The display backlight klight Displa klight Displa klight Displa
improves display contrast in low lighting conditions. When
the "C" terminal is powered, selecting backlight CdL ON
will keep the light on continuously. Select backlight OFF
will keep the light on momentarily after any key is
pressed. When the "C" terminal is not powered, the light
will be on momentarily after any key is pressed no matter
whether the backlight is selected ON or OFF .
11)Select Select Select Select T T T T T emper emper empera a a a a tur emper tur tur ture Displa e Displa e Displa e Display y y y y Adjustment 4 L
Select emper tur e Displa
Allows you to adjust the room temperature display up to
4° higher or lower. Your thermostat was accurately cali-
brated at the factory, but you have the option to change
the display temperature to match your previous thermo-
stat. The current or adjusted room temperature will be
displayed on the left side of the display.
Select F° or C° R Select F° or C° R eadout eadout
12)Select F° or C° R Select F° or C° R Select F° or C° Readout eadout – Changes the display readout eadout
to Centigrade or Fahrenheit as required.
13)Select Filter R Select Filter Re e e e e placement Select Filter R Select Filter R Select Filter R placement placement placement R R R R R eminder and Set placement
Select the "Chang Change Filter Chang Chang Chang e Filter e Filter" reminder On or OFF . If selec- e Filter e Filter
ted On, press MENU MENU MENU MENU MENU to select the time period from 25 to
1975 hours in 25 hours increments. In a typical system,
200 hours (default) of run time is approximately 30 days.
After the selected time of blower operation, the thermostat
will display "Chang Chang Chang Change Filter Chang e Filter e Filter" as a reminder to change or e Filter e Filter
clean your air filter. When "Chang
press MENU MENU MENU MENU MENU button to clear the display and restart the
time to the next filter change.
tion tion tion – This thermostat is tion
Adjustment 4 LO to 4 HI Adjustment 4 L Adjustment 4 L O to 4 HI O to 4 HI O to 4 HI
Adjustment 4 L O to 4 HI
eminder and Set R R R R R un eminder and Set eminder and Set eminder and Set un un un Time un Time Time Time Time
Chang Chang Change Filter Chang e Filter e Filter e Filter e Filter" is displayed,
5