Milwaukee 2676-20 Manual Del Operador página 5

• Press the release button on the tool to ensure it is
ready for operation.
• After 5000 punches, return the tool to a MILWAUKEE
service facility for inspection and maintenance.
Preparing the Material
1. Select the appropriate punch, die and draw stud
for the application. See "Accessories" for chart.
2. Draw cross-hairs to mark the exact location of the
pilot hole.
3. Drill the pilot hole slightly larger than the draw stud.
Using the Quick Connect Assembly
4. Slide the draw stud through the die,
then through the material.
5. Place the punch under/behind the
material and screw onto the draw
stud.
6. Line up cross hairs on the die with
those used to locate the pilot hole
on the material. Tighten the punch
and die securely against each side
of the material to hold the assembly
in place.
7. Rotate the quick connect sleeve to
access the opening in the coupler.
8. Slide the coupler around the ball pull.
9. Rotate the sleeve to lock the ball pull
into the coupler.
Punching the Material
10. Grasp the handle firmly and ensure hands and
body are away from the punch and die.
11. Pull the trigger.
12. When the operation is complete, release the trigger.
13. Push the release button.
14. Rotate the quick connect sleeve and remove the
ball pull from the coupler.
15. When using the Rapid Reset Draw Stud Set,
unconnect the ball pull from the draw stud. When
using the standard draw stud and ball pull, unscrew
the punch from the draw stud.
16. Remove the material. Use caution as the material
edges may be sharp.
Punching without the Quick Connect Assembly
1. Prepare the material as above.
2. Slide the draw stud through the die, then through
the material.
3. Place the punch under/behind the material and
screw onto the draw stud.
4. Line up cross hairs on the die with those used to
locate the pilot hole on the material. Tighten the
punch and die securely against each side of the
material to hold the assembly in place.
5. Grasp the handle firmly and ensure hands and
body are away from the punch and die.
6. Pull the trigger.
7. When the operation is complete, release the trigger.
8. Push the release button.
9. Unscrew the punch from the draw stud and remove
the material. Use caution as the material edges
may be sharp.
MAINTENANCE
To reduce the risk of injury, always
WARNING
unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the tool, battery pack or charger. Contact a
MILWAUKEE service facility for ALL repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage of
parts, or any other condition that may affect the tool
operation. Return the tool, battery pack, and charger
to a MILWAUKEE service facility for repair. After six
months to one year, depending on use, return the
tool, battery pack and charger to a MILWAUKEE
service facility for inspection.
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work prop-
erly, return the tool, charger and battery pack, to a
MILWAUKEE service facility for repairs.
To reduce the risk of personal in-
WARNING
jury and damage, never immerse
your tool, battery pack or charger in liquid or
allow a liquid to flow inside them.
Clean dust and debris from vents. Keep handles
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these include gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household deter-
gents containing ammonia. Never use flammable or
combustible solvents around tools.
For repairs, return the tool, battery pack and charger
to the nearest service center.
ACCESSORIES
Use only recommended accesso-
WARNING
ries. Others may be hazardous.
For a complete listing of accessories, go online to
www.milwaukeetool.com or contact a distributor.
SERVICE - UNITED STATES
1-800-SAWDUST
Monday-Friday, 7:00 AM - 6:30 PM CST
www.milwaukeetool.com
or visit
Contact Corporate After Sales Service Technical
Support with technical, service/repair, or warranty
questions.
Email: metproductsupport@milwaukeetool.com
B e c o m e a H e a v y D u t y C l u b M e m b e r a t
www.milwaukeetool.com to receive important
notifications regarding your tool purchases.
SERVICE - CANADA
Milwaukee Tool (Canada) Ltd
1.800.268.4015
Monday-Friday, 7:00 AM - 4:30 PM CST
or visit www.milwaukeetool.ca
5
Cleaning
Repairs
(1.800.729.3878)