Power Ratings; Product Specifications; Engine Specifications - Craftsman 580.752870 Instrucciones De Uso

Ocultar thumbs Ver también para 580.752870:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

ENGINE TECHNICAL iNFORMATiON
This is a single cylinder, overhead valve (OHV), air cooled
engine. In the State of California, Model 110000 engines
are certified by the California Air Resources Board to meet
emissions standards for 125 hours. Such certification does
not grant the purchaser, owner or operator of this engine
any additional warranties with respect to the performance or
operational life of this engine. The engine is warranted solely
according to the product and emissions warranties stated
elsewhere in this manual.
Power Ratings
The gross power rating for individual gasoline engine
models is labeled in accordancewith SAE (Society of
Automotive Engineers) code J1940 Small Engine Power
& Torque Rating Procedure, and is rated in accordance
with SAE J1995. Torque values are derived at 2600 RPM
for those engines with "rpm" called out on the label and
3060 RPM for all others; horsepower values are derived at
3600 RPM. The gross power curves can be viewed at www.
BRIGGSandSTRATTON.COM. Net power values are taken
with exhaust and air cleaner installed whereas gross power
values are collected without these attachments. Actual
gross engine power will be higher than net engine power
and is affected by, among other things, ambient operating
conditions and engine-to-engine variability. Giventhe wide
array of products on which engines are placed, the gasoline
engine may not develop the rated gross power when used in
a given piece of power equipment. This difference is due to a
variety of factors including, but not limited to. the variety of
engine components (air cleaner, exhaust, charging, cooling,
carburetor, fuel pump, etc.), application imitations, ambient
operating conditions (temperature, humidity, altitude), and
engine-to engine variability. Due to manufacturing and
capacity limitations, Briggs & Stratton may substitute an
engine of higher rated power for this engine.
PRODUCT SPECiFiCATiONS
PressureWasher Specificatiens
Max Outlet Pressure.......................
2,700 PSi*
Max Flow Rate ............................
2.3 GPM
Detergent Mix ........................
Use as directed
Water Supply Temperature..........
Not to exceed IO0°F
Engine Specifications
Bore...............................
2.58 in. (65.6 mm)
Stroke .............................
2.04 in. (51.8 mm)
Displacement . ........................
10.69 in. (175 cc)
SparkPlug
Type: .....................
Briggs & Stratton 692051
SetGapTo: .....................
0.020 inch (O.50mm)
Armature Air Gap: ...........
0.010-0.014in.(O.25-O.36mm)
Valveclearancewith valve springs installedand piston 1/'4in.
(6 mm) past top deadcenter (checkwhen engine is cold).
Intake....................
0.004°0.008in.(O.10-0.20mm)
Exhaust..................
0.004°0.008in.(O.10-O.20 mm)
FuelCapacity...............................
1.6 Quarts
Oil Capacity........................
20 Ounces(0.6 liter)
NOTICE For practical operation, the engine load should
not exceed 85% of rated power. Engine power will decrease
3-1 _2%for each 1,000 ft. (300 m) above sea level and 1%
for each 10° F (5.6° C) above 77° F (25° C). It should operate
satisfactorily at an angle up to 15°.
This pressure washer is rated in accordanceto the
Pressure Washer Manufacturers Association (PWMA)
standard PW101-2010 (Testing and Rating Performance of
Pressure Washers).
17

Publicidad

Tabla de contenido
loading

Tabla de contenido