Bosch GHO 26-82 Professional Manual Original página 13

OBJ_BUCH-446-006.book Page 13 Monday, July 11, 2016 4:10 PM
21 Angle stop*
22 Locking nut for angle adjustment
23 Fastening bolt for rebating depth stop
24 Rebating depth stop*
25 Park rest
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Planer
Article number
Rated power input
Output power
No-load speed
Planing depth
Rebating depth
Planing width, max.
Weight according to EPTA-
Procedure 01:2014
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-14.
Typically the A-weighted noise levels of the product are:
Sound pressure level 84 dB(A); Sound power level 95 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2 2
a =8 m/s , K=1.5 m/s .
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Bosch Power Tools
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 60745-1, EN 60745-2-14,
EN 50581.
Technical file (2006/42/EC) at:
Robert Bosch Power Tools GmbH, PT/ETM9,
70538 Stuttgart, GERMANY
Henk Becker
GHO 26-82
Executive Vice President
0 601 594 1..
Engineering
0 601 594 3..
W 710
W 400
-1
min 16500
Robert Bosch Power Tools GmbH, Division
mm 0 – 2.6
70538 Stuttgart, GERMANY
mm 0 – 9
Stuttgart, 01.01.2017
mm 82
Assembly
kg 2.6
 Before any work on the machine itself, pull the mains
/II
plug.
Changing the Tool
 Be cautious when replacing the planer blades. Do not
grasp the planer blades by the cutting edges. Possible
danger of injury due to the sharp cutting edges of the plan-
er blades.
Use only original Bosch carbide blades (TC).
The carbide blade (TC) has 2 cutting edges and can be re-
versed. When both cutting edges are dull, the planer blade 13
must be replaced. The carbide blade (TC) may not be resharp-
ened.
Disassembling the Planer Blade(s) (see figure A)
To reverse or replace the planer blade 13, rotate the blade
drum 10 until it is parallel to the planer base plate 7.
 Loosen the two fastening screws 12 with the Hex key 14 by
approx. 1 – 2 turns.
 If necessary, loosen the clamping element 11 by giving it a
light blow with a suitable tool (e.g. a wooden wedge).
 Push the planer blade 13 sidewards out of the blade drum
10 with a piece of wood.
Assembling the Planer Blade(s) (see figure B)
The guide groove of the planer blade always ensures continu-
ous height adjustment when replacing or reversing it.
If required, clean the blade seat in the clamping element 11
and the planer blade 13.
When assembling the planer blade, ensure that it is seated
properly in the blade holder of the clamping element 11. The
planer blade must be assembled and aligned centred to the
planer base plate 7. Afterwards tighten the 2 fastening
screws 12 with the Hex key 14.
English | 13
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
1 609 92A 2NJ | (11.7.16)