Briteq BT-PAR 18TC Manual De Instrucciones página 6

ENGLISH
Color Preset Mode
Used to choose one of the 16 standard preset colors. You can also define your own custom color,
based on individual settings for red, green and blue.
 Press the MENU button until CoLo is shown on the display.
 Press the ENTER button to select.
 Use DOWN and UP button to select one of the available options:
 Select one of the preset colors Co 1 to Co16 and press ENTER to confirm.
 Select Manu to make your own color and press ENTER to confirm. Now you can set the 3 colors to
make your own custom color:
 red (red): press ENTER. Then use the DOWN and UP buttons to set the value between 000 and
255. Confirm with the ENTER button. Use the DOWN and UP buttons to select the next color.
 Green (green): press ENTER. Then use the DOWN and UP buttons to set the value between 000
and 255. Confirm with the ENTER button. Use the DOWN and UP buttons to select the next color.
 blue (blue): press ENTER. Then use the DOWN and UP buttons to set the value between 000 and
255. Confirm with the ENTER button. Use the DOWN and UP buttons to select the next color.
 Once the right settings are done; press the MENU button for about 2 seconds to return to running mode.
Led Display
Display on: display is always on.
Display off: display is off when not used.
 Press the MENU button until the display shows LEd.
 Press the ENTER button.
 Use DOWN and UP buttons to select on (display always on) or oFF (display off when not used).
 Once the mode is selected, press the ENTER button to confirm.
 Press the MENU button for about 2 seconds to return to running mode.
Display Inversion
Display inversion: display is readable when the unit is mounted upside down.
 Press the MENU button until the display shows
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to select on (display inversion) or oFF (normal display).
 Once the mode is selected, press the ENTER button to confirm.
 Press the MENU button for about 2 seconds to return to running mode.
Fixture Temperature
 Press the MENU button until the display shows teMP.
 Press ENTER button and the display will show the temperature of the unit.
 To go back to the functions press the MENU button again.
Adjust White balance
Makes it possible to adjust the white color when all colors are at maximum.
 Press the MENU button until baLa is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use the DOWN and UP button to select the red (Red) or Gree (Green) or blue (Blue) color.
 Press the ENTER button, the display starts blinking.
 Use the DOWN and UP button to adjust the value from 125 to 255 and press ENTER to confirm.
 Once the mode has been selected, press the ENTER button to confirm.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Fixture Hours
Used to show the number of working hours of the unit.
 Press the MENU button until FhrS is shown on the display.
 Press the ENTER button to show the number of working hours in the display.
 Press the MENU button for about 2 seconds to return to running mode.
BRITEQ
®
USER MANUAL
(or while inversed)
7/55 BT-PAR 18TC
ENGLISH
Software version:
Used to show the software version of the unit.
 Press the MENU button until ver is shown on the display.
 Press the ENTER button to show the software version of the unit.
 Press the MENU button for about 2 seconds to return to running mode.
OPERATING INSTRUCTIONS
A. Standalone 1unit:
 Just connect the projector to the mains.
 Select one of the automatic modes (ShMd / ChaS) or select a fixed color (CoLo)
 Select the static or sound control mode

IMPORTANT set the Blackout mode to 'NO Blackout' or nothing will happen.
 Refer to chapter HOW TO SETUP to learn how to make the previous settings.
Remark: You can connect a CA-8 remote controller to the unit if you want to have more control.
B. Two or more units in master/slave setup:
 Connect 2 to maximum 16 units together. Refer to the chapter "electrical installation" to learn how to
do this.
 Select one of the automatic modes (ShMd / ChaS) or select a fixed color (CoLo) on the master (the
first projector in the DMX chain)
 If you selected one of the shows (ShMd) on the master, you can set the slave mode for each of the
slave projectors, otherwise put all all slaves to SL 1 so they will copy all functions of the master. (see
chapter HOW TO SETUP the slave mode)
 Connect all units to the mains and put on some music. The units will start working automatically to the
rhythm of the music and show the internal chase programs.

IMPORTANT set the Blackout mode to 'NO Blackout' or nothing will happen.
Remark: You can connect a CA-8 or LEDCON-02 remote controller to the master unit if you want to
have more control over the master/slave operation.
C. Connect the optional CA-8 controller for more control:
The CA-8 controller can only be used in standalone or master/slave mode. Connect the controller to the
CA-8 input of the first unit (master). Now you can control all the connected units:
BUTTON
STANDBY
1.Synchronous strobe
in white color Select one of the
2.The same color different colors.
FUNCTION
chase
3.Different color
strobe
Strobe Color select
MODE
(LED OFF) (LED ON)
D. Connect an optional LEDCON-02 controller for more control:
The LEDCON-02 controller can be considered as a very easy to use DMX controller. Connect the
controller to the DMX-input of the first unit (master). Make sure that the BT-PAR 18TC projectors are all
set to LedC mode. Now you can control all the connected units in 4 or 8channel mode.
IMPORTANT don't forget to perform the automatic addressing on the LEDCON-02 or things will NOT
work as expected! Refer to the user manual of the LEDCON-02 controller for more information.
E. Controlled by universal DMX-controller:
 Connect all units together. Refer to the chapter "Electrical installation for two or more units in DMX-
mode" to learn how to do this (don't forget to address all units properly!)
 Connect all units to the mains and turn on the DMX controller.
Since each unit has its own DMX-address, you can control them individually. Remember that each unit
uses 4 or 6 DMX-channels, depending on the DMX-mode shown. See the different DMX charts below:
BRITEQ
®
USER MANUAL
ACTIONS
To blackout all the fixtures
Select one of the 12 Select one of the
different multi-channel different color fade
shows. modes.
Show select Chase select
(LED slow blinking) (LED fast blinking)
8/55 BT-PAR 18TC