Soporte mural plano y discreto, gama performance, 32 - 70 pulgadas (81 - 178 cm) (29 páginas)
Resumen de contenidos para Amazon Basics B01KBEOL5E
Página 1
STAFFA DI MONTAGGIO A PARETE CON ARTICOLAZIONE PER LA MAGGIOR PARTE DEI TELEVISORI DA 22-INCH (22 POLLICI) A 55-INCH (55 POLLICI) MANUALE DI ISTRUZIONI SOPORTE DE TV PARA PARED ARTICULADO PARA LA MAYORÍA DE LAS PANTALLAS DE 22 A 55 IN (56 A 140 CM) MANUAL DE INSTRUCCIONES ASIN: B01KBEOL5E...
Página 2
SPECIFICATIONS Display Size: 22” to 55” Maximum Load: 80 lbs. (36.3 kg) Mounting Pattern: 100x100, 200x100, 200x200, 300x200, 300x300 400x200, 400x300, 400x400 Tilt Range: -5° to 10° down Profile: 2.375” x 16.125” (60mn x 410mm) CAUTION! This product is for indoor use only! Never use the mount outdoors! CAUTION! This product is for private household use only and therefore may not be used in public places like restaurants or hotels.
Página 3
• Examine the wall you want to install the mount to before you start installation. Make sure that there are no hidden power supply cables, gas pipes, water pipes or other objects hidden in the wall that might be hit by the drill, screws or other hardware. •...
SPÉCIFICATIONS Grandeur de l’écran : 22 po à 55 po Charge maximale : 36,3 kg (80 lbs.) Modèle de montage : 100x100, 200x100, 200x200, 300x200, 300x300 400x200, 400x300, 400x400 Plage verticale : -5° à 10° vers le bas Profil : 60mm x 410mm (2.375” x 16.125”) MISE EN GARDE! Ce produit est destiné...
Página 5
6. Choisissez le bon endroit pour installer la plaque murale. • Assurez-vous que le mur puisse supporter au moins 4 fois le poids de la télévision et du support. Si nécessaire, demandez à un technicien qualifié de renforcer la paroi. •...
Página 6
SPEZIFIKATIONEN Bildschirmgröße: 22 “ bis 55“ Maximalgewicht: 36.3 kg (80 lbs.) Einbauschablone: 100x100, 200x100, 200x200, 300x200, 300x300 400x200, 400x300, 400x400 Neigungsbereich: -5° bis 10° nach unten Profil: 60mn x 410mm (2.375” x 16.125”) ACHTUNG! Dieses Produkt ist nur für den Innengebrauch! Verwenden Sie die Halterung niemals im Freien! ACHTUNG! Dieses Produkt ist für den ausschließlich für den Privathaushalt und kann daher nicht an öffentlichen Orten wie Restaurants oder Hotels...
Página 7
6. Wählen Sie die geeignete Stelle für die Installation der Wandhalter- ung. • Stellen Sie sicher, dass die Wand das vierfache Gewicht des Fern- sehers und der Halterung tragen kann. Falls nötig, holen Sie einen qualifizierten Techniker, um die Wand zu verstärken. •...
Página 8
SPECIFICHE Dimensione schermo: da 22” a 55” Carico massimo: 36.3 kg (80 lbs.) Dima di montaggio: 100x100, 200x100, 200x200, 300x200, 300x300 400x200, 400x300, 400x400 Gamma di inclinazione: da -5° a 10° verso il basso Profilo: 60mn x 410mm (2.375” x 16.125”) ATTENZIONE! Questo prodotto è...
Página 9
6. Scegliere il luogo corretto per installare la piastra a parete. • Accertarsi che la parete sia in grado di sostenere almeno 4 volte il peso della TV e del supporto. Se necessario, far rinforzare la parete da un tecnico qualificato. •...
ESPECIFICACIONES Tamaño de la pantalla: De 22 in a 55 in Carga máxima: 36.3 kg (80 lbs.) Patrón de montaje: 100x100, 200x100, 200x200, 300x200, 300x300 400x200, 400x300, 400x400 Rango de inclinación: De -5 ° a 10 ° hacia abajo Perfil: 60mn x 410mm (2.375” x 16.125”) PRECAUCIÓN Este producto está...
6. Elija el lugar adecuado para instalar la placa de pared. • Asegúrese de que la pared pueda soportar por lo menos 4 veces el peso del televisor y del soporte. Si es necesario, pida a un técnico calificado que refuerce la pared. •Examine la pared en la que desea instalar el soporte antes de empezar la instalación.
Página 12
Leitfaden angegeben. Richten Sie die Installationsschablone mittig über dem Bolzen aus, uchten Sie die Bohrpunkte „A“ „B“ und „C“ mit Bleistiftmarkierungen aus. ASIN B01KBEOL5E Benutzen Sie ein Nivelliergerät, damit sichergestellt wird, dass die Schablone gerade ausgerichtet ist. Bohren Sie vorsichtig drei Löcher durch die entsprechenden Punkte „A“...
Página 13
(EN) INCLUDED PARTS (FR) PIÈCES INCLUSES PARTES INCLUIDAS INCLUDED PARTS PIÈCES INCLUSES (DE) IM LIEFERUMFANG ENTHALTENE TEILE IM LIEFERUMFANG PARTI INCLUSE (IT) PARTI INCLUSE ENTHALTENE TEILE (ES) PARTES INCLUIDAS [A] M4 x 12mm, 4 [C] M4 x 30mm, 4 [J] M6 x 14mm, 4 [L] M6 x 35mm, 4 [M] M8 x 20mm, 4 [OS] M8 x 38mm, 4...
(EN) ATTACHING THE MONITOR PLATE [MP] (FR) FIXER LA PLAQUE DE MONITEUR [MP] (DE) BEFESTIGUNG DER MONITOR-PLATTE [MP] (IT) FISSAGGIO DELLA PIASTRA PER LO SCHERMO [MP] (ES) CÓMO FIJAR LA PLACA DEL MONITOR [MP] (EN) SELECT THE CORRECT SCREW Before beginning, test several of the screws in your hardware kit to find the correct size and length for your television.
Página 16
(EN) REMOVE THE SECURITY SCREWS (FS) The Monitor Plate (MP) was shipped pre-installed to the Extension Arm (EA). Before you begin, remove the two Security Screws (FS) as shown in and separate the two components. Do not throw out the security screws. (FR) ENLEVER LES VIS DE SÉCURITÉ...
(EN) DECIDE IF ADAPTER PLATES [AP] ARE NECESSARY Compare to the mounting holes on the back of your television. (FR) DÉCIDER SI DES PLAQUES D’ADAPTATION [AP] SON NÉCESSAIRES Comparer aux trous de fixation au dos du téléviseur. (DE) ENTSCHEIDEN SIE SICH, OB ADAPTER-PLATTEN [AP] ERFORDERLICH SIND Vergleichen Sie sie mit den Montagelöchern auf der Rückseite Ihres Fernsehers.
(EN) IF USING THE ADAPTER PLATES [AP]: Attach the Adapter Plates [AP] to the Monitor Plate [MP] using eight M8 x 10mm Screws [BE]. (FR) SI LES PLAQUES D’ADAPTATION [AP] SONT UTILISÉES : Fixer les plaques d’adaptation [AP] à la plaque de moniteur [MP] à l’aide de huit vis M8 x 10mm [BE].
Página 20
(EN) ATTACH MONITOR PLATE [MP] TO TELEVISION Attach the Monitor Plate [MP] using the correct TV Mounting Screws [A, J, or M] and Washers [R or S] as shown. Do not place the Washers between the monitor plate and the TV. (FR) FIXER LA PLAQUE DE MONITEUR [MP] AU TÉLÉVISEUR Fixer la plaque de moniteur [MP] avec les vis [A, J, ou M] de fixation de TV et les rondelles [R ou S] correctes comme sur l’illustration.
Página 21
(EN) Use spacers [E or P] if the Monitor Plate [MP] does not fit firmly against the back of the television, such as when the back of the television is curved, contains larger re- cessed mounting holes, or some other obstruction is in the way. The Monitor Plate must rest securely on the spacers, and should not be loose.
(EN) INSTALLING THE WALL MOUNT IN WOOD (FR) POSER LE SUPPORT MURAL SUR DU BOIS (DE) INSTALLATION DER WANDBEFESTIGUNG IN HOLZ (IT) INSTALLAZIONE DEL SUPPORTO A PARETE SU LEGNO (ES) CÓMO INSTALAR EL SOPORTE DE PARED EN MADERA (EN) FIND THE WOOD STUD Using a stud finder, find the exact location of the stud to which you want to attach the wall mount.
(EN) DETERMINE HEIGHT LOCATION OF TELEVISION Measure the distance from the bracket holes to the top and bottom of the TV to determine the center mounting position. Measure from the floor up, and make small marks on the wall to help you determine the desired TV height. Using a level, line up the Installation Template [IT] with your pencil markings and tape it into place.
Página 24
[LV] [IT] (EN) Height to bottom of TV (FR) Hauteur jusqu’au bas du téléviseur (DE) Höhe zum unteren Teil des TVs 16" (IT) Altezza alla parte inferiore del televisore (SP) Altura hasta la parte inferior del TV (406 MM)
(EN) FOR MASONRY INSTALLATIONS, SEE PAGE 28. (FR) POUR UNE POSE SUR DE LA MAÇONNERIE, VOIR PAGE 28. (DE) FÜR INSTALLATIONEN IN MAUERWERK, SIEHE SEITE 28. (IT) PER INSTALLAZIONI A MURO, VEDERE A PAGINA 28. (ES) PARA INSTALACIONES EN MAMPOSTERÍA CONSULTE LA PÁGINA 28. (EN) DRILL PILOT HOLES Follow directions on the Installation Template (IT) carefully.
Página 26
Leitfaden angegeben. Richten Sie die Installationsschablone mittig über dem Bolzen aus, uchten Sie die Bohrpunkte „A“ „B“ und „C“ mit Bleistiftmarkierungen aus. ASIN B01KBEOL5E Benutzen Sie ein Nivelliergerät, damit sichergestellt wird, dass die Schablone gerade ausgerichtet ist. Bohren Sie vorsichtig drei Löcher durch die entsprechenden Punkte „A“...
Página 27
(EN) INSTALL THE EXTENSION ARM (EA) Install the Extension Arm (EA) using three Lag Bolts [TS] in the “A”, “B” and “C” holes. Do not tighten Lag Bolts completely. After the Wall Mount is on the wall, use a level to make sure the Wall Mount is vertically level. (FR) POSER LE BRAS ARTICULÉ...
Página 28
(EN) MOUNTING TO SOLID CONCRETE OR CINDER BLOCK (FR) POSE SUR DU BÉTON PLEIN OU DES PARPAINGS (DE) MONTAGE AN FESTBETON ODER SCHLACKENBETONBLOCK (IT) MONTAGGIO SU CALCESTRUZZO O BLOCCHI IN CEMENTO (ES) MONTAJE EN CONCRETO SÓLIDO LADRILLOS DE ESCORIAS (ES) After you have determined your desired TV location, Line up the Installation Template [IT] to ensure you will not drill into any mortar joints.
Página 29
(EN) DRILL PILOT HOLES Carefully drill three holes using a 5/16" (or 8mm) masonry drill bit in the “A” and “B” locations noted on the Installation Template. Each hole should be at least 3" (76mm) deep. (FR) PERCER LES TROUS GUIDES Percer soigneusement trois trous avec une mèche à...
Página 30
(EN) DO NOT DRILL INTO MORTAR JOINTS! DRILL TOP HOLES AT LEAST 1" (25.4 MM) FROM THE JOINTS. USE A NEW DRILL BIT TO ENSURE OPTIMUM HOLDING ABILITY. DO NOT USE A HAMMER DRILL! (FR) NE PAS PERCER DANS LES JOINTS DE MORTIER ! PERCER LES TROUS SUPÉRIEURS À...
(EN) INSERT ANCHORS Remove Template [IT] and insert Anchors [U8]. (FR) ENFONCER LES CHEVILLES Enlever le gabarit [IT] et enfoncer des chevilles d’ancrage [U8]. (DE) DÜBEL EINFÜGEN Entfernen Sie die Schablone [IT] und führen Sie Dübel [U8]. (IT) INSERIRE I TASSELLI Togliere lo schema [IT] e inserire i tasselli [U8].
Página 32
(EN) INSTALL THE EXTENSION ARM (EA) Install the Extension Arm (EA) using three Lag Bolts [TS] in the “A”, “B” and “C” holes. Do not tighten Lag Bolts completely. After the Wall Mount is on the wall, use a level to make sure the Wall Mount is vertically level. (FR) POSER LE BRAS ARTICULÉ...
Página 33
[EA] [U8] [TS] (EN) DO NOT OVER TIGHTEN LAG BOLTS [TS]! (FR) NE PAS FORCER SUR LES TIRE-FOND [TS] ! (DE) ZIEHEN SIE DIE ANKERBOLZEN [TS] NICHT ZU FEST! (IT) NON SERRARE ECCESSIVAMENTE I BULLONI [TS]! (ES) NO AJUSTE DEMASIADO LOS TIRAFONDOS [TS]!
(EN) PREPARE THE MOUNT FOR INSTALLING THE TV Before you place the television on the wall, first move the Extension Arm [EA] into the straight extended position and make sure the Wall Plate [WP] is level on the wall. Check the Tilt Adjustment. It needs to be tight so it will not tilt during installation.
(EN) MOUNT THE TELEVISION With the help of an assistant, lift the television and guide the Monitor Plate [MP] onto the Extension Arm [EA] as shown. Once safely on the mount, continue to hold the TV securely while installing the Security Screws [FS], using the Hex Tool [HT].
Página 37
[MP] [EA] [HT] (EN) Exercise caution when removing the television from the mount to avoid equipment damage or personal injury. (FR) Lors du décrochage du téléviseur, faire preuve de précaution pour éviter les dommages matériels et corporels. (DE) Gehen Sie vorsichtig bei der Abnahme des TVs von der Befestigung um, um das Gerät nicht zu beschädigen oder um keine Körperverletzungen zu verursachen.
(EN) USING THE TILT FEATURE Once the television is secured on the Extension Arm (EA), you can adjust the tilt of the television by loosening both Tilt Screws using the Hex Tool (HT). Tilt the television into the desired position, then fully tighten the Tilt Screws again with the Hex Tool.
(EN) ADJUST THE TV LEVEL Once the television is secured on the Extension Arm (EA), you can adjust the level of the television by slightly loosening the two Leveling Screws on the back of the Extension Arm (EA) with the Hex Tool (HT). Once loosened, have an assistant hold the TV in the desired position, then fully tighten the Leveling Screws again with the Hex Tool.
(EN) USING THE CABLE MANAGEMENT FEATURE Feed the Audio Video cables through the Cable Management Cover (CC) as shown. Attach the Cover to the bottom portion of the Extension Arm (EA) by pressing upward until the Cover snaps into place. Remove extra cables if the Cover will not properly attach.
Warranty Information To o b ta in a co py o f t he wa r r a n ty f o r thi s p ro d uct : Visit amazon.com/AmazonBasics/Warranty — or — Contact Customer Service at 1-866-216-1072 Feedback Love it? Hate it? L e t u s k no w wi th a c us t ome r rev i ew.
Informations sur la garantie P our obten ir un e c opi e de la gar a nti e d e ce p ro d ui t : Visitez amazon.com/AmazonBasics/Warranty — ou — Contactez le service client au +1-866-216-1072 Vos commentaires Vous adorez? Vous détestez? Laissez-no u s v otre av is .
Página 46
Garantie Hier e rhal ten Si e ei ne K o pi e der P rodu k t ga r a n t i e : amazon.com/AmazonBasics/Warranty — o de r — Wenden Sie sich an den Kundendienst unter +1-866-216-1072 Feedback Gefällt Ihnen das Produkt? Oder überzeugt Sie das Produkt nicht?
Informazioni sulla garanzia P e r o t t e n ere u na c op ia de ll a ga ra n z ia per que st o pro do tto : Visitare amazon.com/AmazonBasics/Warranty — oppu re — contattare il servizio clienti al numero +1-866-216-1072 Feedback Ti piace? Non ti piace? S c i v i u n a rec e nsi one .
Información sobre la garantía Par a ob te ne r u na c o pi a de l a g ar ant ía de este produ cto: Visita amazon.com/AmazonBasics/Warranty — o — ponte en contacto con el servicio de Atención al Cliente a través del +1-866-216-1072 Opinión ¿Te gusta? ¿Lo odias? Há...
Página 52
a m a z o n . c o m / A m a z o n B a s i c s M A D E I N C H I N A R E V. 0 9 2 6 1 6...