Cautions With Stainless Steel - Skymsen SI-315HD-1 Manual De Instrucciones

SKYFOOD EQUIPMENT LLC - SERVICE
For questions or assistance with products FLEETWOOD by SKYMSEN and SKYMSEN,
call SKYFOOD EQUIPMENT Toll Free : 1-800-503-7534, 24h Customer support, or visit
the Customer Service section of www.skyfood.us.
SKYFOOD'S LIMITED WARRANTY
Unless otherwise specified, new FLEETWOOD by SKYMSEN and SKYMSEN products,
excluding accessories, sold by SKYFOOD EQUIPMENT, LLC. ("SKYFOOD"), for use only
in the continental United States (collectively, "Products" or singularly, "Product"), are
warranted to be free from defects in materials and workmanship for a period of one (1)
year from the date of purchase by the original purchaser/user ("End User"). Several new
products and accessories may be warranted for a period other than one (1) year while
others may be subject to travel limitations, as specified on the products Instruction Manual.
Proof of purchase must be presented; if not this warranty will be VOID. No warranty is
given or implied to a subsequent transferee or any other third party. This warranty is
expressly conditional upon SKYFOOD being notified of any defects in materials or
workmanship within five (5) days of its occurrence, within the warranted time period. If a
notice of a claim under this warranty is timely made by the End User, SKYFOOD or a
SKYFOOD's designated service company ("Service Company"), will repair or replace the
Product, at SKYFOOD's discretion, subject to the additional conditions hereinafter
described.
This warranty shall not apply if damage occurs from improper installation or maintenance
performed by an unauthorized service company ("Service Company"), wrong voltage, nor
to the extent that Products or parts have been used other than in conformance with
operating and maintenance instructions, subjected to misuse or abuse or damaged by
accident, acts of God, abnormal use, stress or any other matter unrelated to SKYFOOD,
and beyond its reasonable control. This warranty does NOT cover service labor and
travel to perform adjustments on products and/or accessories. In addition to wear and
tear of certain items, such as, but not limited to; glass parts, blades, stones, chopper
cutting knives, plates, slicing knives, cutting disc, gaskets, oil changes, sealing tape, heat
seal wires, worm gears, self-lubricating bushings, carbon brushes for electric motors, and
other parts expendable by nature and that need to be replaced frequently. Electrical
components are subject to natural wear and tear, and are NOT covered by this
warranty. THIS WARRANTY EXCLUDES ALL ORAL, STATUTORY, EXPRESS OR
IMPLIED WARRANTIES WHICH MAY BE APPLICABLE TO SKYFOOD, INCLUDING,
BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY AND
FITNESS FOR PARTICULAR PURPOSE. Under no circumstances shall SKYFOOD be
liable for loss of use, revenue or profit or for incidental or consequential damages.
SKYFOOD shall under no circumstances be liable for any loss, damage, concealed
damage, expense or delay of goods for any reason when said goods are in the custody,
possession or control of third parties selected by SKYFOOD to forward, enter, clear,
transport, or render other services with respect to such goods. The sole and exclusive
remedy for breach of any warranty is limited to the remedies provided in the paragraph
above.
All products held at non-commercial facilities or domiciles, must be taken or shipped,
shipping charges prepaid, either to SKYFOOD's facility or a SKYFOOD's designated
3.2.1 Remove the Upper Door # 04 (Pct.01). To do so unlock it using the Upper Door Lock #
19 (Pct.01), and lift it.
3. 2. 2 Remove the Lower Door # 17 (Pct.01) , to do so unlock it using the lower lock # 20 (
Pct 01) , and lift it .
3.2.3 Loose the Blade turning the Regulator # 01 (Pct.01) handle counter clockwise and take
the Blade off the Wheels # 05 and # 21 (Pct.01).
3.2.4 To remove the Upper Wheel, loose the Nut # 01 (Pct.04) with a 13 mm spanner. Using
the same spanner turn counter clockwise the Screw # 02 (Pct.04) until it comes out of the Wheel shaft
hole. Remove the Upper Wheel # 05 (Pict.01) pulling it out.
3.2.5 To remove the Lower Wheel remove the Staple # 12 (Pct.01) that locks the Lower
Wheel # 21 (Pct.01) and pull it out.
3.2.6 Wash all the parts with water and neutral soap and dry them.
3.2.7 Never use hard or sharp objects such as: KNIVES, HOOKS, or similar, to clean meat
hanging on the Saw Doors. Use a plastic brush to remove it and to clean.
3.2.8 To reassemble the removable parts, proceed the inverse path.
Put Vaseline in the Wheels # º05 and # 21 (Pct.01) hole each 15 days. Check the Blade # 08
(Pct.01) position. The right position is with its teeth towards the front side of the Saw and

3.3 Cautions with Stainless Steel:

The Stainless Steel may present rust signs, which ARE ALWAYS CAUSED
BY EXTERNAL AGENTS, especially when the cleaning or sanitization is not
constant and appropriate.
The Stainless Steel resistance towards corrosion is mainly due to the
presence of chrome, which in contact with oxygen allows the formation of a very thin
protective coat. This protective coat is formed through the whole surface of the steel,
blocking the action of external corrosive agents.
When the protective coat is broken, the corrosion process begins, being
possible to avoid it by means of constant and adequate cleaning.
Cleaning must always be done immediately after using the equipment. For
such end, use water, neutral soap or detergent, and clean the equipment with a soft
cloth or a nylon sponge. Then rinse it with plain running water, and dry immediately
with a soft cloth, this way avoiding humidity on surfaces and especially on gaps.
The rinsing and drying processes are extremely important to prevent stains
and corrosion from arising.
IMPORTANT
pointed down.
06