Makita HW1200 Manual De Instrucciones página 3

• Do not abuse extension cords and do not
yank on cords to disconnect them.
Keep cords away from heat and sharp edges.
•
• Always disconnect the extension cord
from the receptacle before disconnecting
the product from the extension cord.
7. The electric supply connection shall be made
by a qualified electrician and comply with IEC
60364-1. It is recommended that the electric
supply to this machine should include either
a residual current device that will interrupt the
supply if the leakage current to earth exceeds
30 mA for 30 ms or a device that will prove the
earth circuit.
Power tool use and care
1. Read all the instructions before using the
product.
2. Know how to stop the high pressure washer
and bleed pressures quickly. Be thoroughly
familiar with the controls.
3. High pressure jets can be dangerous if mis-
used. The jet must not be directed at people,
live electrical equipment, or the machine itself.
4. This machine is not intended for use by per-
sons (including children) with reduced physi-
cal, sensory, or mental capabilities, or lack of
experience and knowledge.
5. Children should be supervised to ensure that
they do not play with the appliance.
6. Do not spray flammable and/or toxic liquids.
This may cause an explosion, intoxication, or
damage to the machine.
7. Do not direct the jet against yourself or others
in order to clean clothes or foot-wear.
High-pressure hoses, fittings and couplings
8.
are important for the safety of the machine.
Use only hoses, fittings and couplings recom-
mended by the manufacturer.
Follow the instructions when changing
9.
accessories.
10. Keep handles dry, clean, and free of oil or grease.
11. Stay alert – watch what you are doing.
12. Do not operate the product when fatigued or
under the influence of alcohol or drugs.
13. Do not run the high pressure washer without
water for longer than one minute. It will dam-
age the motor, resulting in malfunction.
14. Always turn off the power and shut off the
water mains when leaving the high pressure
washer unattended.
15. Be wary of the kickback. The trigger gun
recoils when the high pressure jet is ejected
from the nozzle. Hold the trigger gun firmly to
prevent accidental injuries.
16. Check for damaged or worn parts before use.
Also make sure that the hose is properly con-
nected and there is no leakage during oper-
ation. Operating the machine with functional
defects may cause an accident.
17. This machine has been designed for use with
the cleaning agent supplied or recommended
by the manufacturer. The use of other cleaning
agents or chemicals may adversely affect the
safety of the machine.
18. Do not pull the cord and/or hose to move the
high pressure washer body. This will damage
the cord, hose, and connecting parts and
result in a short circuit or functional defects.
19. Do not put heavy objects on the hose or let
vehicles drive over it.
20. Always discharge the residual pressure in the
trigger gun before disconnecting the hose.
21. When connecting the hose to the water mains,
observe the instructions of your local water-
works department or company.
Service
Follow the maintenance instructions specified
1.
in the manual.
2. To ensure machine safety, use only original
spare parts from the manufacturer or approved
by the manufacturer.
3. Have your high pressure washer serviced by
a qualified repair person using only identi-
cal replacement parts. This will ensure that
the safety of the high pressure washer is
maintained.
In case of breakdown or malfunction of the
4.
high pressure washer, immediately switch it
off and remove the mains plug. Contact your
local dealer or service center.
Additional safety warnings
1. Comply with the requirements of the local
water supply company.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product.
MISUSE or failure to follow the safety rules stated
in this instruction manual may cause serious
personal injury.
Symbols
The followings show the symbols used for tool.
volts
amperes
hertz
alternating current
Class II Construction
Do not direct the jet at people including
yourself, animals, and live electrical
equipments.
Not suitable for connection to the potable
water mains.
3 ENGLISH