Genie 1022 Manual De Instrucciones
  1. Manuales
  2. Marcas
  3. Genie Manuales
  4. Abridores de Puertas de Garage
  5. 1022
  6. Manual de instrucciones

Genie 1022 Manual De Instrucciones

Ocultar thumbs Ver también para 1022:
Tabla de contenido

Publicidad

Enlaces rápidos

Descargar este manual
Installer:
Leave this manual
with homeowner.
Homelink
is a registered trademark of
®
Johnson Controls Technology Company.
Car2U
®
is a registered trademark of
Lear Corporation.
© The Genie Company 2010.
X900-745
PN# 3642036534, 2/26/2010 REV.1
A L W AY S AT Y O U R C O M M A N D
Models 1022/1024/1042
Includes INTELLICODE
Safe-T-Beam
®
For use only with sectional doors. Your Residential
Opener comes with a Rail Assembly which is standard
for up to a 7 foot high door.
Homelink
and Car2U
®
For Answers and Assistance:
1.800.354.3643
or visit www.geniecompany.com
SAVE THIS MANUAL FOR FUTURE REFERENCE
GARAGE DOOR OPENERS
Remote Control
®
System must be installed to close door.
compatible
®

Publicidad

Tabla de contenido
loading

Manuales relacionados para Genie 1022

Resumen de contenidos para Genie 1022

  • Página 1 1.800.354.3643 or visit www.geniecompany.com Homelink is a registered trademark of ® Johnson Controls Technology Company. SAVE THIS MANUAL FOR FUTURE REFERENCE Car2U ® is a registered trademark of Lear Corporation. © The Genie Company 2010. X900-745 PN# 3642036534, 2/26/2010 REV.1...

  • Página 2: Safety Information

    If you have questions or do NOT understand the information presented, contact The Genie Company or an authorized Genie ®...

  • Página 3: Tabla De Contenido

    TABLE OF CONTENTS OPENER FEATURES INTELLICODE ® Rolling Code Security System. SECTION ......... PAGE An electronic rolling code system that enhances the security of SAFETY INFORMATION .

  • Página 4: Pre-Installation Check List

    They are as follows: The Genie Company recommends that you read and fully understand all information and instructions contained herein before choosing a "Do-it-yourself" installation. Any questions should be directed to The Genie Company or an authorized Genie ®...

  • Página 5: Typical Sectional Door Installation

    TYPICAL SECTIONAL DOOR INSTALLATION FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM Pg. 19 Pg. 13 Pg. 12-13 TYPICAL SUPPORT ADDED BRACKET HEADER BRACKET (NOT PROVIDED) MOUNTING BOARD BRACES POWER CORD (APPROX. 45 IN.) TO 120V GROUNDED OUTLET EXTENSION SPRING TORSION SPRING Pg. 14 NOTE: This opener is designed for use with SECTIONAL doors only.

  • Página 6: Recommended Tools

    RECOMMENDED TOOLS FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM Pencil 3/16" Drill Bit Carpenter’s level Drill Wire strippers Adjustable wrench Ratchet Tape measure Safety Glasses Step ladder Hammer 1/4", 7/16", 3/8" and Phillips screwdriver 1/2" Sockets PARTS IDENTIFICATION - Not Shown Full Size . ARRANGING BOX CONTENTS FOR ASSEMBLY ORGANISATION DU CONTENU DE LA BOÎTE POUR LE MONTAGE DISPOSICIÓN DEL CONTENIDO DE LA BOLSA PARA EL MONTAJE...

  • Página 7: Important

    FASTENERS - Shown Full size (See Parts List below for full description.) BAG NO. DESCRIPTION QUANTITY RAIL SECTION CLAMP RAIL CLAMP BOLT – 5/16''-18 x 5/8'' HEX FLANGE NUT – 5/16''-18 BOLT – 5/16''-18 x 1/2'' Rail Clamp Bolt - 5/16"-18 x 5/8" CLEVIS PIN, LONG –...

  • Página 8: Key Illustrations

    1-PIECE RAIL HARDWARE ASSEMBLED VIEW FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM Power Cord Rail with chain Power Head Trolley Slide CHAIN Release or s nt ac Knob . Co ci ng ut or r fo b ra di st tu re IO N uf ac io ns m an...

  • Página 9: Important Installation Instructions

    (If you have until instructed to do so. questions or do not understand an instruction, call The 6. Locate the control button: Genie Company or an authorized Genie ® Dealer.) • Within sight of door, 2. Install only on a properly balanced sectional garage door.
  • Página 10 Rail Assembly for CHAIN DRIVE OPENER CHAIN DRIVE RAILS NOTE: For split rail clamps, nuts, and bolts locate Bag 0 from Box 1. Chain Rail Center Rail 3. Remove the two rail sections that are not connected to the chain and place them on floor (Fig.
  • Página 11 POWER HEAD & RAIL ASSEMBLY 5/16"-18 x 1/2" Assembly for CHAIN DRIVE OPENER Bolts NOTE: Handle carefully! Drive chain can slide out of rail. NOTE: For power head and rail assembly locate Bag 1 from Box 1. NOTE: Copy serial number from power head frame and record it on warranty page.

  • Página 12: Installation

    INSTALLATION FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM b) - extend HEADER AND DOOR vertical line MOUNTING BRACKETS: 2-1/2" WARNING Header bracket must be fastened to garage d) - final framing. Do NOT fasten to drywall, particle c) - door at height mark board, plaster or other such materials.
  • Página 13 MOUNTING THE OPENER: HEADER BRACKET 1. Getting started. • Position assembled rail on wall next to header bracket (Fig. 2-4). – Place material on floor under power head to protect from scratching. (A box, stool, or VIEW similar device may be needed to clear a FROM ABOVE torsion spring.) (not to scale)
  • Página 14 Contact door manufacturer or distributor for a bracing kit. centerline The Genie Company is not responsible for even with or damage caused due to improperly braced door. above top roller NOTE: For door bracket and bolts locate Bag 4 FIG.

  • Página 15: Wall Button Installation

    WALL BUTTON INSTALLATION FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM Wire from WARNING power head to wall control. Verify there is NO power to the opener before installing wall button wires and wall button. CAUTION Staples which are too tight can cut or pinch wires. Cut or pinched wires can cause the wall button to stop working.
  • Página 16 3.Securely fasten wires. Locking Clips wire guide Terminal • Securely fasten wires to ceiling and Holes wall using insulated staples provided. – Use insulated staples. – Staples should be snug only. Insulated • If rear cover is attached to power head, Staple remove it.

  • Página 17: Safe-T-Beam System Installation

    – If not: center of tongue bracket a) Mounting bracket extensions are available through an authorized Genie ® Dealer. b) Blocks of wood, etc. may be substituted for FIG. 4-2 Mounting brackets extensions. • Center bracket on your mark (Fig. 4-2).
  • Página 18 3b. Wiring (pre-wired). • Route wire from wall to Safe-T-Beam ® sensors Wall Wall (Fig. 4-5b). Green • Splice pre-wiring to shortened sensor wire, match wire pairs dash-to-dash and Source Sensor plain-to-plain. - Trim sensor wire to approximately one foot (1 ft) from sensor.

  • Página 19: Connecting To Power

    • Replace motor cover and rear cover and will not be influenced if the Safe-T-Beam ® re-energize the circuit. obstructed. NOTE: The Genie Company is not responsible for 2. If the Safe-T-Beam ® is obstructed before the charges resulting from work preformed by an garage door fully closes, the door will not close.

  • Página 20: Limit Switches & Force Adjustment

    DOOR LIMITS FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM Limit Controls location WARNING on power head. • Severe injury or death can result if the door NOTE: Set Close Travel Limit closing force is set too high. before setting Open Travel • Never increase the door closing force above the Limit for unit to operate minimum required to move the door.

  • Página 21: Carriage Lock

    CARRIAGE LOCK DOOR The Carriage Lock can be manually engaged or disengaged. • To disengage Carriage Lock – Pull handle towards opener power head. • To engage Carriage Lock – Pull handle towards door. LOCK UNLOCK TO RECONNECT TO RELEASE PULL TOWARD PULL TOWARD DOOR...

  • Página 22: Contact Reverse Test

    UP/DOWN FORCE 1. By turning the Down Force Control clockwise, CLOSE Up Force the DOWN force can be increased. By turning Control OPEN Adjustment the Down Force Control counter-clockwise, CLOSE the DOWN force can be decreased. Set the DOWN force level at the minimum force required (Increasing Force to close door without reversing.

  • Página 23: Programming Remote Controls

    PROGRAMMING REMOTE CONTROLS WARNING A moving door can cause serious injury or death. 1. Keep people clear of opening while door is moving. NOTE: To program a 2. Do NOT allow children to play with opener, Homelink and Car2U ® ®...

  • Página 24: Battery/Visor Clip Installation

    REMOTE CONTROL BATTERY REPLACEMENT AND VISOR CLIP INSTALLATION 1. Battery replacement. Slide out • To open gently push straight out on battery cover lock tab as shown (Fig. 8-1). • Flip open battery cover. – Remove old battery. • Make sure new battery is facing proper direction (Match battery polarity with symbols inside battery cover) (Fig.

  • Página 25: Safety Instructions

    Have a trained door system technician make repairs to cables, spring assemblies, and other hardware. SAVE THESE INSTRUCTIONS. ® If you have any questions, please do not hesitate to contact Genie customer service at: 1.800.354.3643 MAINTENANCE 2.

  • Página 26: Wiring Diagram

    CIRCUIT WIRING DIAGRAM FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM Opener circuit wiring diagram. This wiring diagram is for reference only. Diagrama del circuito del abrelatas. Este diagrama es sólo para referencia. Schéma de câblage de l’ouvreur. Ce schéma de câblage est indiqué à titre de référence uniquement. Opening Cover May Cause Electric Shock.

  • Página 27: Troubleshooting Guide - Opener

    WARNING: If you suspect a problem with the garage door hardware or springs, contact an authorized Genie ® Dealer or a trained door system technician, or contact The Genie Company at 1-800-35-GENIE. Door will only run in • Check door balance, condition, and door spring.

  • Página 28: Troubleshooting Guide - Power Head Led

    • Door obstruction going down • Check for obstruction, remove. • Door obstruction going up – Check door spring – Contact The Genie Company at 1-800-35-GENIE 2 BLINKS, Pause • Programming incomplete • Set UP LIMIT programming (Repeat) •...

  • Página 29: Transmitter Compliance Statement

    TRANSMITTER COMPLIANCE STATEMENT Transmitters comply with all United States and Canadian legal requirements as of the date of manufacture. No warranty is made that they comply with all legal requirements of any other jurisdiction. If transmitters are to be used in another country, the importer must determine compliance with any local laws and regulations which may differ from United States and Canadian requirements prior to use.

  • Página 30: Warranty

    Limited Warranty GMI Holdings, Inc. d/b/a The Genie Company ("Seller") warrants to the original purchaser of the below identified opener Model 1022 or opener Model 1024 or opener Model 1042 (“Product”), subject to all of the terms and conditions hereof, that the Product and all components thereof will be free from defects in materials and workmanship for the following period(s) of time, measured from the date of purchase: MOTOR - Seller warrants the motor for a period of FIVE (5) YEARS.
  • Página 31 This page left blank.
  • Página 32 This page left blank.
  • Página 33 This page left blank.

Este manual también es adecuado para:

10241042

Tabla de contenido