Cleanup; Overnight Storage; Long-Term Storage - Titan ED655 Manual Del Propietário

Ocultar thumbs Ver también para ED655:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

cleanup

Overnight Storage

Shutdown
1. Turn the pressure control knob counterclockwise to the
minimum setting.
2. Turn the PRIME/SPRAY knob to PRIME to release system
pressure.
3. Trigger the gun to remove any pressure that may still be in the
hose.
4. Lock the gun by pushing the gun trigger
lock to the locked position.
5. Turn the motor switch to OFF and
unplug the sprayer.
6. For latex materials only, pour 1/2 cup
water slowly on the top of the paint to
prevent the paint from drying. For other
materials, seal the paint hopper with the
hopper cover keeping the return tube in
the paint.
7. Wrap the spray gun assembly in a damp cloth and place it in a
plastic bag. Seal the bag shut.
8. Place the sprayer in a safe place out of the sun for short-term
storage.
Startup
1. Remove the gun from the plastic bag.
2. Stir the water into the paint for latex materials. Remove the
hopper cover from the paint hopper and stir the paint for all
other materials.
3. Check to be sure that the PRIME/SPRAY knob is set to PRIME
and that the pressure is completely reduced.
4. Plug sprayer in and turn the motor switch to ON.
5. After the sprayer is primed, turn the PRIME/SPRAY knob to
SPRAY and gradually turn the pressure control knob clockwise
to increase the pressure.
6. Test the sprayer on a practice piece and begin spraying.
English

Long-Term Storage

Do not allow paint to build up on the motor or the
motor will overheat. Do not allow flammable solvents
to come in contact with the motor or they could ignite.
NOTE: you will need a bucket, cleaning solution, a
toothbrush, a wrench and cleaning rags.
NOTE: If spraying with latex paint, use warm soapy water
for cleaning. If using oil or alkyd-based paints, use
mineral spirits or paint thinner.
IMPOrTaNT: Do not use mineral spirits or paint thinner on latex
paint, or the mixture will turn into a jelly-like substance which is
difficult to remove.
clearing the Paint Hopper
1. Lock the gun by pushing the gun trigger
lock to the locked position.
2. Turn the pressure control knob
counterclockwise to the minimum
setting.
3. Turn the PRIME/SPRAY knob to PRIME.
4. Turn the motor switch to OFF.
5. Direct the return tube into the original
paint bucket.
6. Turn the motor switch to ON.
7. Turn the pressure control knob to 1/2 maximum pressure.
This will draw the remaining paint in the paint hopper
through the pump, up the return tube, and into the paint
bucket.
8. Turn the pressure control knob counterclockwise to the
minimum pressure setting.
9. Trigger the gun to relieve pressure and lock the gun.
10. Remove the spray tip and guard and place them into a
container of water or appropriate solvent for the type of
material with which you are painting.
11. Fill the paint hopper with water or an appropriate solvent for
the type of material with which you are painting.
12. Direct the return tube into a waste bucket.
13. Increase the pressure to 1/2 the maximum pressure. Let the
water or solvent circulate for 2-3 minutes to flush paint out of
the pump, the paint hopper, and the return tube.
clearing the Paint Hose
1. To save paint left in the hose, release the gun trigger lock and
carefully trigger the gun with the spray tip removed against
the inside of the paint container.
2. Turn the pressure control knob counterclockwise to the
minimum pressure setting.
3. Turn the PRIME/SPRAY knob to SPRAY.
4. Turn the pressure control knob slowly until paint starts to
flow into the bucket. As soon as the water or solvent starts to
come into the bucket, release the trigger.
5. Change to clean water or solvent, point the gun to the side
of the waste bucket, and continue circulating for another 5
minutes to thoroughly clean the hose, pump and spray gun.
6. Turn the pressure control knob counterclockwise to its lowest
setting.
8
© Titan Tool. All rights reserved.

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido