Independent Operation; Operation With A Dmx Controller; Dmx Connection - IMG STAGELINE PARC-56/WS Manual De Instrucciones

WARNING Install the spotlight safely and
expertly. When installing it at a place
where people may walk or sit under
it, additionally secure it (e. g. via a
safety rope on the mounting bracket;
fasten the safety rope in such a way
that the maximum falling distance of
the unit will not exceed 20 cm).
1. Install the spotlight via its mounting brackets (7),
e. g. with a stable mounting screw or a support
for lighting units (C hook) to a cross bar.
To align the spotlight, release the two locking
screws (6) of the mounting brackets. Adjust the
desired inclination of the spotlight and fasten
the screws.
2. Alternatively, set up the spotlight on its own:
Fold out the mounting brackets underneath the
spotlight and use them as a stand. Then fasten
the locking screws.
4.2 Colour filter and barn doors
For radiating coloured light, insert a colour filter or
a coloured filter foil (e. g. LCF-... series from "img
Stage Line") into the colour filter frame (4) pro-
vided. Slide the frame into the slot at the front of the
spotlight and secure it with the clip (2).
To reduce the light beam angle, barn doors
(accessory) are available:
Barn doors
PARC-56B
PARC-64B
PARC-64B / SI
Insert the barn doors into the outer slot at the front
of the spotlight and secure them with the clip (2). To
additionally secure the door barns, screw the
4 screws supplied into the threaded holes of the
door barns.
4.3 Switching on
WARNING To prevent damage to your eyes,
never look directly into the light
source.
Please note that fast changes in light-
ing may trigger epileptic seizures with
photosensitive persons or persons
with epilepsy!
Connect the plug of the mains cable (5) to a
mains socket (230 V~ / 50 Hz). Thus, the spotlight is
switched on, its display (9) will indicate the menu
item most recently selected and go out after 30 sec-
onds. As soon as you press one of the control but-
tons (8), the display will light up again for 30 seconds.
Suitable for
PARC-56 / WS
PARC-64 / WS
PARC-64SI / WS
5 Operation
To select the operating mode and the different func-
tions, use the menu via the control buttons MENU,
ENTER, UP and DOWN (8). Figure 2 on page 2
shows the selection of the modes and functions via
the menu and the indications on the display (9).

5.1 Independent operation

For independent operation, use the control buttons
(8) to set the brightness, to activate the strobo-
scope function and to set the flash rate.
1) Press the button MENU repeatedly until the dis-
play indicates
2) Press the button ENTER once or twice so that
the display will indicate the brightness adjusted
( ... ).
3) To set the desired brightness, press the buttons
UP and DOWN.
4) To activate the stroboscope function, press the
button ENTER once again so that the display
will indicate .
5) To set the flash rate (
buttons UP and DOWN.
6) To change the brightness of the flash, press the
button ENTER to return to the menu item for the
brightness. To change the value, press the but-
ton UP or DOWN.
7) To deactivate the stroboscope function, set the
flash rate to
Important: Do not exit the menu item for the bright-
ness or the flash rate with the button MENU before
switching off the spotlight. If you do, the spotlight
will remain dark when you switch it on again.

5.2 Operation with a DMX controller

For operation via a DMX light controller (e. g. DMX-
1440 or DMX-510USB from "img Stage Line"), the
spotlight is equipped with three DMX control chan-
nels. DMX is short for digital multiplex and means
digital control of several DMX units via a common
control cable. The functions of the channels and
the DMX values can be found in chapter 5.2.3.

5.2.1 DMX connection

For DMX connection, 3-pole XLR connectors with
the following pin configuration are provided:
Pin 1 = ground, 2 = DMX-, 3 = DMX+
For connection, use special cables for DMX signal
transmission (e. g. cables of the CDMXN series
from "img Stage Line"). For cable lengths exceed-
ing 150 m, it is generally recommended to insert a
DMX level matching amplifier (e. g. SR-103DMX
from "img Stage Line").
.
... ), press the
.
GB
9