Union Special 4000 Serie Manual De Instrucciones página 21

Ref.
No. Part No.
52.. 4001452
52-1- 4001452-1
52-2.. 4001452-2
53.. 4001453
53-1.. 4001453-1
54.. 4001454
55.. 4001455
56.. 4001456
57A.. 4001457A
57.. 4001457
57-1.. 4001480
57-2.. 4001457-2
57-3.. 4001457-3
59.. 4001459
60.. 4001460
61.. 4001461
58.. 4001458
58-1.. 4001458-1
58-2.. 4001458-2
62.. 4001462
63.. 4001463
64.. 4001464
64-1.. 4001464-1
64-2.. 4001464-2
65.. 4001465
66.. 4001466
66-1.. 4001466-1
67.. 4001467
68.. 4001468
69.. 4001469
69-1.. 4001469-1
69-2.. 4001469-2
70.. 4001470
71.. 4001471
72.. 4001472
73.. 4001473
74.. 4001474
75A. 4001475A
75.. 4001475
75-1. 4001475-1
76.. 4001476
77.. 4001477
77-1.. 4001477-1
78.. 4001478
79.. 4001479
80.. 4001480
81.. 4001481
82.. 4001482
83.. 4001483
84.. 4001484
84-1. 4001484-1
85.. 4001485
85-1. 4001485-1
86.. 4001486
87.. 4001487
88.. 4001488
MAIN SHAFT & LOOPER ASSEMBLY PARTS
Description
Mainshaft..............................................................................................................
Screw.............................................................................................................
Oil Felt............................................................................................................
Collar, Mainshaft............................................................................................
Screw, #5-40N.C. X 3/8"................................................................................
"O" Ring............................................................................................................
Washer, thrust.................................................................................................
Bushing, Mainshaft (rear)................................................................................
Connecting Rod & Eccentric Assembly with Bearing Rod Ends................
Connecting Rod & Eccentric Assembly...............
Screw...... .....................................................................................................
Screw, (cone point)........................................................................................
Screw (flat point) ............................................................................................
Washer, Internal tooth, 5/16"............................................................................
Nut, Hex Head.................................................................................................
Bearing, Rod End...........................................................................................
Cam Looper Assembly...................................................................................
Screw, #10-32N.F. X 5/8"(cone point).......................................................
Screw, #10-32N.F. X 1/2"..............................................................................
Arm & Stud Cam Follower Assembly............................................................
Cam Follower Stud...........................................................................................
Cam Follower Arm....... ...............................................................................
Screw, #5-40N.C. X 5/8"........ .....................................................................
Washer, Flat ..............................................................................................
Nut, Hex Head..............................................................................................
Collar, Looper Shaft.........................................................................................
Screw, #5-40N.C. X 1/2"..............................................................................
Shaft, Looper..................................................................................................
Bushing, Looper Shaft......................................................................................
Looper Holder.......... ......................................................................................
Screw, #8-32N.C. X 3/16"...........................................................................
Screw, #5-40N.C. X 1/4"............................................................................
Looper..............................................................................................................
Bushing, Mainshaft (front) .............................................................................
Screw, #8-32N.C. X 5/16".....................................................................................
Washer, internal tooth #8.............................................................................
Angle Clip........................................................................................................
Carrier Block Assembly with Slide...............................................................
Carrier Block, Feed Dog...........................................................................
Screw, #6-40N.F. X 3/8"..............................................................................
Washer, Felt.....................................................................................................
Slide...................................................................................................................................................
Knife Slide...........................................................................................................
Feed Dog.........................................................................................................
Washer, Flat #8 ................................................................................................
Screw, #8-32N.C. X 1.......................................................................................
Screw, #10-32N.F. X 3/8".................................................................................
Washer, Lock #10................................................................................................
Bracket, Knife...................................................................................................
Knife, Stantionary.......................................................................................
Screw, #3-48N.C. X 5/16".........................................................................
Knife, Moving...........................................................................................
Screw, #3-48N.C. X 3/16..........................................................................
Bushing, Knife Shaft..................................................................................
Shaft, Knife................................................................................................
Spring, Knife Tension.................................................................................
21
Amt.
Req.
1
1
1
1
1
1
3
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1