General Characteristics - Astralpool LumiPlus S-Lim 1.11 Manual De Instalación Y Mantenimiento

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 7
ENGLISH
IMPORTANT: The instruction manual you are holding includes essential information on the safety measures to be im-
plemented for installation and start-up. Therefore, the installer as well as the user must read the instructions before
beginning installation and start-up.
Keep this manual for future reference.
To achieve optimum performance of the LumiPlus S-Lim Projector, follow the instructions provided below:
1. VERIFY THE CONTENTS OF THE PACKING:
The following accessories are included inside the box:
• Unit projector
• Crosshead mount
• Installation and maintenance manual
LumiPlus S-Lim 1.11
Pool
Light
RGB
Concrete
Monocolor
RGB-DMX
RGB
Prefabricated
Monocolor
RGB-DMX

2. GENERAL CHARACTERISTICS:

This projector has been designed to be used totally submerged in water. It is a Class III electric apparatus with very low
safety voltage (12V with alternating current).
The projector compiles with IPX8 degree of protection (resistance to penetration of dust, solid bodies and humidity) at a
nominal immersion depth of 2 m.
This projector compiles with international safety standards for lights, especially the EN 60598-2-18 standard. LIGHTS
PART 2: SPECIFIC REQUIREMENTS SECTION 18 LIGHTS FOR SWIMMING POOLS AND SIMILAR APPLICATIONS.
The manufacturer is not responsible in any circumstances for assembly, installation or start-up of any electric components
which have been inserted or handled at locations other than its own premises.
3. INSTALLATION:
• To correctly light a swimming pool we recommend you:
Install a projector in the range LumiPlus 1.11 every 20 m² of water surface.
Install a projector in the range LumiPlus 2.11 every 25 m² of water surface.
Note: Recommendation valid for light coloured pools. In darker coloured pools or stainless steel pools we recommend
oversizing the proportion of projectors per m².
• In order to prevent glare, the projectors should be installed so that they face away from the residence or usual view of
the swimming pool.
• In the event that lighting is used in training or competition pools, the projectors should be installed on the sides to
prevent glare on the swimmers.
• In installations where you want to replace a conventional spotlight by a LED projector, using the existing wiring, it is
strongly recommended to use underwater resin splicing. It is not recommended to use silicone to try to seal the con-
nection point of the wires. The spotlight should not be handled internally under any circumstances as this would lead
to losing the guarantee.
• The projector should be placed on the wall of the pool at approximately 400-700 mm from the water surface (Fig. 5).
The method of fastening the crosshead mount to the pool wall varies depending on whether it is a projector for concrete
pools or prefabricated pools.
• In the LumiPlus 2.11 models it is essential that the direction of the projector is adequate, situating "TOP" on the top.
• Warranty booklet
• Bag of fastenings
• Manual for electrical connection
MODELS AVAILABLE ACCORDING TO CHARACTERISTICS
Faceplate
ABS
Stainless Steel
56022
56023
56030
56031
56026
56027
56024
56025
56032
56033
56028
56029
LumiPlus S-Lim 2.11
Pool
Light
RGB
Concrete
Monocolor
RGB-DMX
RGB
Prefabricated
Monocolor
RGB-DMX
3
Faceplate
ABS
Stainless Steel
56010
56011
56018
56019
56014
56015
56012
56013
56020
56021
56016
56017

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Lumiplus s-lim 2.11

Tabla de contenido