Setting Up And Assembly - Thomashilfen EASyS Manual Del Usuario

EASyS Modular seating system
Seat depth
Seat width
Back height *
Lower leg length
hip angle
Knee angle
Foot angle
turning range of seat
Seat tilt-in-space (on A chassis)
height adjustment arm support
Size of arm support (w x h)
Size of foot rest (w x d)
Overall dimensions (l x w x h)
Folded dimensions (l x w x h)
Weight (seat) *
carrying capacity (seat)
* without headrest

Setting up and assembly

Adjustments / adaptations shall be carried out by trained or instructed experts (e.g. medical device consultants of a medical device
dealer) only.
The seat can be removed from the A chassis without needing any tools. Push the click lever below the seat unit forwards and take
the seat unit off the receiver adapter of the chassis forwards. Proceed in reverse order to insert the seat.
cAUtION: Always ensure the click lever engages audibly. Then make sure the seat has clicked into place by pulling it
forwards.
Commercially available tools are required for mounting / dismounting the accessories. Separate mounting instructions and user
manuals are enclosed with the accessories. If they should be missing, you can download the instructions in the download section of
our website www.thomashilfen.com.
Mounting the foot rest
The foot rest is to be fixed to the knee joints. Place the grid joints one upon the other and connect them with the screws (from the
inside), washers (from the outside), and wing nuts (from the outside). (Fig. 1)
Lateral backrest upholstery / side upholstery (EASyS)
Take the two shorter upholstery pieces from the upholstery sets and put them over the lateral tubes. The snap fasteners should point
inwards. The Velcro for fastening the upholstery is situated on each outer side of the curved sections of the back plate. Velcro the upholstery
to the back plate with the side which is pointing inwards. (Fig. 2) Close the upholstery completely with the Velcro at the back. (Fig. 3)
Attach the longer upholstery pieces to the upholstery already mounted using the snap fasteners. (Fig. 4) In addition, velcro each longer
upholstery to the inner sides of the curved section of the back plate.
Lateral backrest upholstery (EASyS Modular)
Make sure that the short side of the upholstery is pointing outwards before mounting. (Fig. 5) Put the lateral backrest upholstery over
the lateral tube and velcro it on the inner and outer side to the curved section of the back plate. Close the Velcro completely – also
over the knurled screw. (Fig. 6-7)
Receiver for sun and rain cover
Both EASyS and EASyS Modular are equipped with receivers for the sun and rain cover. (Fig. 8)
Seat upholstery
Velcro the seat upholstery to the seat plate. Fix the two lower Velcro fasteners around the tubes of the foot rest.
Inserting the seat unit
Place the seat unit on the rear crossbar and move the seat forward and down. The EASyS click system engages automatically and
audibly. (Fig. 9)
Removal of the seat unit
To remove the seat unit, push the click-lever under the seat forward and take the seat unit off the chassis forward. (Fig. 9)
14
EASyS Modular Size 1
16 - 28 cm / 6.3 - 11"
20 - 30 cm / 7.9 - 11.8"
26 - 42 cm / 10.2 - 16.5"
17 - 30 cm / 6.7 - 11.8"
90° to 140°
90° to 180°
78° to 100°
180°
-10 to + 35°
10 - 14 cm / 3.9 - 5.5"
21 x 10 cm / 8.3 x 3.9"
29 x 18 cm / 11.4 x 7.1"
85 x 41 x 57 cm
33.5 x 16.1 x 22.4"
89 x 41 x 38 cm
35 x 16.1 x 15"
7.9 kg / 17.4 Ib
35 kg / 77.2 Ib
EASyS Modular Size 2
24 - 35 cm / 9.4 - 13.8"
26 - 35 cm / 10.2 - 13.8"
32 - 52 cm / 12.6 - 20.5"
25 - 36 cm / 9.8 - 14.2"
90° to 140°
90° to 180°
78° to 100°
180°
-10° to +35°
12 - 18 cm / 4.7 - 7.1"
29 x 12 cm / 11.4 x 4.7"
33 x 21 cm / 13 x 8.3"
64 x 48 x 77 cm
25.2 x 18.9 x 30.3"
90 x 48 x 60 cm
35.4 x 18.9 x 23.6"
9.6 kg / 21.2 Ib
40 kg / 88.2 Ib