Guarantee Conditions - Gumotex BARAKA Manual De Usuario

cement drum in the second net bag. No sharp objects should
remain in the canoe.
Lay out the defl ated canoe on a clean surface and straighten
all its parts. Fold the sidewall cylinder lengthwise to overlap
the seal of the bottom by approx. 10 cm. Then fold the cylinder
lengthwise again, this time from the centre towards the exter-
nal edge. The top edge of the drum is approx. 5 cm from the
edge of the bottom. Repeat this procedure with the second
sidewall cylinder. Then fold the stern approx. (25–30) cm from
the end and gradually fold the canoe towards the bow, do not
roll up the drain sleeve – leave it loose on the bottom. At the
end fold the bow of the boat by approx. 30 cm and then fold up
towards the stem, so that you can put the reinforcement drum
between the folded corpus with its valve on the hole for the
drain sleeve, complete the packing. Fix the folded canoe with
the enclosed compression belt and insert it in the carry bag.
Finally, place the seats and the remaining accessories in the
bag, fasten the compression belts on the bag.
Expel the air from the bag, roll up the insertion end and fasten
it with clips.
6. Treatment and Storage
The rubber surface coating of the boat is sensitive to oils, gas-
oline, toluene, acetone, kerosene and similar thinning agents.
Prior to storing a dirty boat, wash it down with warm soapy
water. Rinse the boat with fresh water after using the boat in
seawater. It is recommended to check the state of the infl ation
valves and the safety relief valves. If a valve is not airtight, it is
possible to unscrew the valve body from the boat with the use
of a special valve-key and clean its membrane with a strong jet
of water or compressed air. Prior to storage, it is recommen-
ded to rub the surface of the canoe with an agent intended for
the treatment of such surfaces, which has cleaning properties,
and which impregnates the material to prevent further dirtying,
or which is capable of forming a protective UV-fi lter. Never use
agents containing silicon when treating your boat. Store the
clean and dry product in a dark dry place at a temperature of
(15 - 35) °C, at least 1.5 m from any radiant heat source and
out of the reach of rodents. During longterm storage, it is reco-
mmended to infl ate the boat for 24 hours from time to time to
avoid fatiguing the fold lines. It is also recommended to have
the boat serviced by the manufacturer's authorized service
station at least once every two or three years.
Proper care and treatment of the boat will increase its service
life.

7. Guarantee Conditions

The guarantee period is 24 months and is calculated from the
date of sale.
The producer provides cost-free repairs or replacement of
faulty components for material faults or production faults.
The warranty does not cover any damage of the air chambers
resulting from higher than the prescribed working pressure.
8. Boat Repairs
You can easily repair a damaged boat yourselves by means of
the accompanying gluing set.
Gluing:
•
mark out the damaged area on the boat and choose an
appropriately sized patch;
•
the surfaces of both patch and place to be glued must be
clean, dry and without traces of old glue;
•
we recommend degreasing both surfaces with acetone in
order to achieve a perfect bond;
10
•
spread a thin layer of glue on both surfaces to be glued and
repeat this step once the fi rst layer has dried;
•
after the second layer has dried, press the patch fi rmly on
the damaged place, weigh down or use a rolling pin on
a fl at surface.
For minor repairs (punctures), it is possible to re-infl ate the
boat and continue using it after waiting for approx. 30 minutes;
after more serious repairs, you should wait for 24 hours before
using the repaired boat. Complicated repairs should be per-
formed by the manufacturer or at authorized service stations.
Guarantee repairs and post-guarantee repairs are provi-
ded by the manufacturer:
GUMOTEX, a. s.
Mládežnická 3062/3a
690 75 Břeclav
Czech Republic
9. Product Disposal Method
The product should be disposed of at municipal waste dispo-
sal sites.
10. Packaging Disposal Method
Cardboard – recycle as the indicated symbol directs.
PE-LD plastic wrap (low-density branched polyethylene) – re-
cycle as the indicated symbol directs.
11. Type Parameters Tag
Each boat is provided with its own Type Parameters Tag which
displays the most important technical parameters.
Please follow these values. Above all, do not overload the boat
and maintain the recommended maximum pressures in the air
chambers.
Drawing and legend
Explanation of the symbols used:
maximum operational pressure
maximum number of people
maximum load