Setting The Dmx Start Address; Dmx Channels And Functions; Temperature Indication And Overheat Control; Cleaning The Spotlight - IMG STAGELINE PARC-56/WS Manual De Instrucciones

1) Connect the DMX INPUT (1) to the DMX output
of the light controller or to the DMX output of
another DMX-controlled unit .
2) Connect the DMX OUTPUT (3) to the DMX input
of the following DMX unit . Connect the output of
this DMX unit to the input of the following DMX
unit etc . until all DMX-controlled units have been
connected in a chain .
3) To prevent interference in signal transmission, in
case of long cables or a multitude of units con-
nected in series, terminate the DMX output of the
last DMX unit in the chain with a 120 Ω resistor
(> 0 .3 W): Connect a corresponding terminating
plug (e . g . DLT-123) to the DMX output jack .

5.2.2 Setting the DMX start address

For separate control of all DMX units connected to
the light controller, each unit must have its own start
address . Example: If the first DMX channel of the
spotlight is to be controlled by the controller via DMX
address 17, set the start address on the spotlight to
17 . All other DMX channels of the spotlight will be
automatically assigned to the following addresses
(i . e . 18 and 19 in case of start address 17) .
1) Press the button MENU repeatedly until
appears on the display .
2) Press the button ENTER . The start address adjusted
( ...
3) To set the desired address, press the buttons UP
and DOWN . Now the spotlight can be operated
with the light controller .
Notes: When the menu item
on the display and DMX signals are available at the DMX
input (1), the dot at the right end of the display will flash .

5.2.3 DMX channels and functions

DMX DMX
channel value
1 000 – 255
000
2
001 – 255
251 – 255
000 – 010
3
011 – 255
DMX channels
➂
All rights reserved by MONACOR
reproduced in any form or by any means for any commercial use.
10
) will be indicated .
, or
Function
brightness 0 %  100 %
response of brightness control
slow response
response very slow  fast
immediate response
stroboscope off
stroboscope slow  fast
INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may be
®
5.3 Temperature indication and
overheat control
The spotlight is equipped with an overheat control .
When the temperature inside the spotlight is too
high, the spotlight will be switched off . After cool-
ing down, the spotlight will be switched on again
automatically . To indicate the inside temperature:
1) Press the button MENU repeatedly until
appears on the display .
2) Press the button ENTER .
display .
3) Press the button ENTER again . The inside temper-
ature (in °C) is indicated on the display .
4) To exit the menu branch, press the button MENU .

6 Cleaning the Spotlight

Clean the plastic pane in front of the LEDs at regular
intervals or as required . This is the only way to ensure
that light will be radiated at maximum brightness .
Before cleaning, disconnect the mains plug from
the socket. Only use a soft clean cloth and a mild
detergent . Then carefully wipe the plastic pane dry .
For cleaning the other parts of the housing, only
use a soft clean cloth . Never use any fluid; it may leak
into the spotlight and damage it .
7 Specifications
Data protocol: . . . . . . . . . . DMX 512
Number of DMX channels: 3
appears Light source: . . . . . . . . . . . white COB LED
Power consumption
PARC-56 / WS: . . . . . . . .
PARC-64 / WS: . . . . . . . . 100 W
Beam angle: . . . . . . . . . 60°
Colour temperature: . . . 5600 K
Power supply: . . . . . . . . . . 230 V/ 50 Hz
Power consumption
PARC-56 / WS: . . . . . . . .
PARC-64 / WS: . . . . . . . . 110 VA max .
Dimensions
PARC-56 / WS: . . . . . . . . ∅ 185 mm × 210 mm
PARC-64 / WS: . . . . . . . . ∅ 220 mm × 260 mm
Weight
PARC-56 / WS: . . . . . . . . 2.5 kg
PARC-64 / WS: . . . . . . . . 3.2 kg
Subject to technical modification .
will appear on the
50 W
60 VA max .