Makita M9000 Manual De Instrucciones página 4

ENGLISH
(Original instructions)
1 Shaft lock
2 Switch trigger
3 Lock lever
4 Wheel guard
5 Screw
6 Bearing box
7 Lock nut
8 Depressed center grinding
wheel
SPECIFICATIONS
Model
Depressed center wheel diameter
Max. wheel thickness
Spindle thread
Rated speed (n) / No load speed (n
Overall length
Net weight
Safety class
• Due to our continuing program of research and
development, the specifications herein are subject to
change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for grinding and cutting of metal and
stone materials without the use of water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
For public low-voltage distribution systems of
between 220 V and 250 V.
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under
unfavorable mains conditions can have adverse effects
to the operation of other equipment. With a mains
impedance equal or less than 0.24 Ohms it can be
presumed that there will be no negative effects. The
mains socket used for this device must be protected with
a fuse or protective circuit breaker having slow tripping
characteristics.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
4
Explanation of general view
9 Inner flange
10 Lock nut wrench
11 Abrasive cut-off wheel/diamond
wheel
12 Wheel guard for abrasive cut-off
wheel/diamond wheel
13 Outer flange 78
14 Inner flange 78
15 Exhaust vent
M9000
180 mm
6.0 mm
) 8,500 min
0
466 mm
5.4 kg
/II
ENE091-1
ENF002-2
ENF100-1
GEA010-1
16 Inhalation vent
17 Commutator
18 Insulating tip
19 Carbon brush
20 Brush holder cap
21 Screwdriver
M14 or 5/8" (country specific)
–1
GRINDER SAFETY WARNINGS
Safety Warnings Common for Grinding or Abrasive
Cutting-Off Operations:
1. This power tool is intended to function as a
grinder or cut-off tool. Read all safety warnings,
instructions, illustrations and specifications
provided with this power tool. Failure to follow all
instructions listed below may result in electric shock,
fire and/or serious injury.
2. Operations such as sanding, wire brushing or
polishing are not recommended to be performed
with this power tool. Operations for which the
power tool was not designed may create a hazard
and cause personal injury.
3. Do not use accessories
specifically designed and recommended by the
tool manufacturer. Just because the accessory can
be attached to your power tool, it does not assure
safe operation.
4. The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and fly apart.
5. The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
6. Threaded mounting of accessories must match
the grinder spindle thread. For accessories
mounted by flanges, the arbour hole of the
accessory must fit the locating diameter of the
flange. Accessories that do not match the mounting
hardware of the power tool will run out of balance,
vibrate excessively and may cause loss of control.
M9001
230 mm
6.0 mm
–1
6,600 min
466 mm
5.7 kg
/II
GEB129-1
which are not