Using The Appliance - Clatronic ICM 3594 Instrucciones De Servicio

4. Fig. D: Attach the outlet unit to the bottom of the housing.
Hold the outlet with the lever positioned on the right side.
Turn the unit through 45°. It must click into place and the
lever must be in the middle position.
Tip: Looking into the housing from above will facilitate the
assembly of the appliance.
5. Make sure the sealing ring on the outlet of the bowl is
positioned properly.
Fig. E: Put the mounting ring on a table. Place the bowl in
the ring. Use the guiding lugs inside the ring as well as the
recessed track on the outside of the bowl. Move the ring to
the upper edge of the bowl. Hold the ring and at the same
time turn the bowl anti-clockwise. The guiding lugs of the
ring must lock into the upper recesses of the bowl.
6. Fig. F: Place the bowl into the housing. Make sure the
outer guiding lug of the mounting ring locks into the groove
on the rear housing. Gently press down the bowl in order to
securely connect it to the outlet unit.
7. Fig. G: Place the assembled unit (fig. B: lid with motor
housing and stirring attachment) on the bowl. The mains
cable is located on the rear. Lock the lid by turning it clock-
wise until tight.
Preparations
1. Check the bowl for any damage. Do not use the bowl if
leaking. Leaking cooling agent is not poisonous, but a
leaking bowl will affect the result of the ice cream making
process.
2. Attach the mounting ring to the bowl as described above (fig.
E).
3. Put the bowl into the freezer for at least 12 hours. The
freezer or freezer compartment should maintain a tempera-
ture of at least - 18°C.
NOTE:
• The bowl must be dry.
• Make sure the bowl stands upright. The cooling
agent inside the bowl must settle evenly.
• If the freezer compartment is not high enough,
remove the mounting ring.
4. Prepare an ice cream mixture. Ideal amount: approx.
600 - 700 ml.
• Sugar must have dissolved completely.
• When making ice cream with fruits, only use soft, seed-
less fruits that are mashed (pureed). You may also add
fruit juice.
• If you wish to add pieces of fruits, nuts, brittle or
alcohol, only add these ingredients to the finished ice
cream. Let the stirring tool stir a few more times.
NOTE:
Alcohol impairs the freezing process.
• Put the ice cream mixture into the fridge until starting
the ice cream making process. Having a temperature
of less than + 10°C will shorten the time of the ice
cream making.
Instructions for use
• The appliance must be assembled completely and
switched on before filling the ice cream mixture into the
bowl. That prevents the ice cream mixture from freezing to
the inner walls of the bowl.
• The outlet unit must be closed. (Lever up)
• Do not overfill the bowl! Ideal amount: approx. 600 -
700 ml. The volume of the ice cream will increase during
the freezing process.
• Do not insert any objects such as fingers, spoons or similar
into the filler hole while the appliance is operating.
• Preparation time varies, depending on:
• the recipe,
• the ambient temperature,
• the temperature of the ice cream mixture.
• Do not leave the appliance unattended during operation.
Constantly check the consistency of the ice cream mixture
in order not to miss the time slot for soft ice cream.
• An ice cream cone can only work during a certain time slot.
The ice cream must not be too runny or viscous either.
• Do not interrupt the stirring process, even when dispensing
the first ice cream cone.
IMPORTANT: Turn off the appliance immediately if
• the ice cream becomes viscous,
• the stirring attachment slows down or does not turn any
more,
• hearing loud motor noise.
In such cases, proceed as follows:
• Remove the stirring attachment from the ice cream in
order for it not to freeze.
• Remove the ice cream from the bowl using a silicone or
wooden spoon. Do not use any metal spoons in order
not to scratch the coating inside the bowl.
• Do not use the outlet unit.
• Let the motor cool down.

Using the appliance

WARNING: Risk of burning from cold!
• If possible, hold the chilled bowl only on the mounting
ring.
• If you have not installed the mounting ring earlier, protect
your hands e.g. with a dishtowel when taking the bowl
from the freezer.
1. Remove the chilled bowl from the freezer. Assemble the
appliance as described under "Assembly of the appliance".
2. Close the outlet valve: Position the lever upwards.
3. Place a bowl underneath the outlet.
4. Connection to the mains:
• Before plugging in the appliance, check if the mains
voltage matches. Refer to the rating label for the
specifications of the appliance.
• Connect the appliance to a certified wall socket only.
39