Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL PRESSITO Manual De Instrucciones Original

•
Switch in the middle: OFF
•
Switch to the right: Low-pressure operation
6.2 Compressor compressed air operation
(Fig. 1a, 1b, 2, 7)
•
To inflate objects with compressed air, use
the compressed air hose (5).
•
Connect the adapter of the compressed air
hose to the object you wish to inflate.
•
Depending on what you are inflating, also use
the adapters (7, 8, 9) or other adapters availa-
ble from retail stores.
•
The pressure at the compressed air hose will
be displayed in the display (11).
•
The unit of the displayed pressure can be se-
lected with the button (15). The pressure can
be displayed in units of [bar], [PSI] or [kPa].
•
The button (14) allows the desired pressure
to be reduced.
•
The button (16) allows the desired pressure
to be increased.
•
Switch on the equipment by moving the se-
lector switch (12) to the compressed air ope-
ration position (see 6.1.).
•
The compressor will then pump until the pre-
set pressure on the display is reached, then it
will switch off.
•
Warning! Observe the information supplied
by the tire manufacturer and the vehicle ma-
nufacturer relating to the recommended tire
pressure.
•
Warning! This equipment is not calibrated!
For a calibrated measurement value, check
the actual tire pressure using a calibrated me-
ter after you have inflated the tires yourself,
e.g. at a petrol station.
•
Just before it is switched off, the pressure
which is shown in the display can be 0.05 –
0.2 bar higher than the preselected pressure,
because of overpressure in the air hose.
•
Allow the compressor to cool down for about
5 minutes after every 5 minutes of operation
in order to prevent overheating.
6.3 Low-pressure blower operation
(Fig. 1a, 3, 4)
6.3.1 Suctioning air (Fig. 3, 7)
•
To suction out objects with a large volume
until they are empty (e.g. deflating an air
mattress, etc.), connect the air hose (3) to the
extractor connection (13).
•
Connect the air hose to the object you wish
to deflate.
Anl_PRESSITO_SPK9.indb 22 Anl_PRESSITO_SPK9.indb 22
GB
•
Switch on the equipment by moving the se-
lector switch (10) to the low-pressure operati-
on position (see 6.1.).
•
Switch off the equipment once the object has
been sufficiently deflated.
6.3.2 Infl ating (Fig. 4, 7)
Warning! When using the equipment to infl ate
objects, check the information and safety instruc-
tions provided by the manufacturer.
•
To inflate objects with a large volume (e.g.
inflating an air mattress, etc.), connect the air
hose (3) to the inflating connection (4).
•
Connect the air hose to the object you wish
to inflate.
•
Switch on the equipment by moving the se-
lector switch (12) to the low-pressure operati-
on position (see 6.1.).
•
Switch off the equipment once the object has
been sufficiently inflated.

7. Replacing the power cable

Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always take the battery out of the equipment
and pull out the power plug before starting any
cleaning work.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
- 22 -
11.06.2019 16:14:58 11.06.2019 16:14:58