Additional Safety Rules; Functional Description - Makita KP312S Manual De Instrucciones

ENGLISH
1 Knob
2 Scale plate
3 Switch trigger
4 Lock-off button
5 Restart button
6 Pins
7 Edge fence (Guide rule)
8 Rear base
9 Foot
10 Planer blade
11 Front base
SPECIFICATIONS
Model
Planing width
Planing depth
No load speed
Overall length
Net weight
Safety class
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for planing wood.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

ADDITIONAL SAFETY RULES

1. Rags, cloth, cord, string and the like should
never be left around the work area.
2. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
3. Use only sharp blades. Handle the blades very
carefully.
4. Be sure the blade installation bolts are securely
tightened before operation.
5. Hold the tool firmly.
6. Keep hands away from rotating parts.
7. Before using the tool on an actual workpiece, let
it run for a while. Watch for vibration or wobbling
that could indicate poor installation or a poorly
balanced blade.
Explanation of general view
12 Hex wrench
13 Installation bolt
14 Socket wrench
15 Drum plate
16 Set plate screw
17 Set plate
18 Planer blade
19 Adjusting screw
20 Drum
21 Wrench holder
22 Chip guide
KP312S
312 mm
0 – 3.5 mm
–1
12,000 min
551 mm
18 kg
/II
ENB045-2
23 Nozzle assembly
24 Joint
25 Hose
26 At the start of planing
27 At the end of planing
28 Front roller
29 Limit mark
30 Screwdriver
31 Brush holder cap
8. Make sure the blade is not contacting the work-
piece before the switch is turned on.
9. Wait until the blade attains full speed before cut-
ting.
10. Keep at least 200 mm away from the tool at all
times.
11. Always switch off and wait for the blades to
come to a complete stop before any adjusting.
12. Never stick your finger into the chip chute.
Chute may jam when cutting damp wood. Clean
out chips with a stick.
13. Do not leave the tool running. Operate the tool
only when hand-held.
14. When leaving the planer, switch off and set it
with the front base up on a wooden block, so
that the blades do not contact anything.
15. Always change both blades or covers on the
drum, otherwise the resulting imbalance will
cause vibration and shorten tool life.
16. Wait for complete run-down before putting the
tool aside.
17. Use only Makita blades specified in this manual.
SAVE THESE INSTRUCTIONS.

FUNCTIONAL DESCRIPTION

CAUTION:
Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
Adjusting depth of cut (Fig. 1)
The depth of cut can be adjusted within a range of 0 –
3.5 mm. Turn the knob on the front of the tool until the
pointer is aligned with the desired cutting depth on the
scale. Set the depth of a cut observing the maximum
depth which is limited by width according to the following
table.
Corelation of width of cut and maximun depth of cut
Width of cut
0 – 150 mm
150 – 240 mm
240 – 312 mm
Maximum depth of cut
3.5 mm
2 mm
1.5 mm
5