Bosch GWS 600 Professional Manual Original página 14

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 27
OBJ_BUCH-161-008.book Page 14 Thursday, August 25, 2016 3:27 PM
14 | English
Additional Safety and Working In-
structions
 Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
 Use suitable detectors to determine if utility lines are
hidden in the work area or call the local utility company
for assistance. Contact with electric lines can lead to fire
and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage or
may cause an electric shock.
 Release the On/Off switch and set it to the off position
when the power supply is interrupted, e. g., in case of a
power failure or when the mains plug is pulled. This pre-
vents uncontrolled restarting.
 Dust from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health and cause allergic reactions, lead to res-
piratory infections and/or cancer. Materials containing
asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suitable
for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
 Prevent dust accumulation at the workplace. Dust can
easily ignite.
 Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
 After breakage of the grinding disc during operation or
damage to the holding fixtures on the protection
guard/power tool, the machine must promptly be sent to
an after-sales service agent for maintenance. For address-
es, see section "After-sales Service and Application Ser-
vice".
 Adjust protection guard in such a manner that sparking
toward the operator is prevented.
 Do not touch grinding and cutting discs before they
have cooled down. The discs can become very hot while
working.
 Actuate the spindle lock button only when the grinder
spindle is at a standstill. Otherwise, the machine may be-
come damaged.
 After mounting the grinding tool and before switching
on, check that the grinding tool is correctly mounted
and that it can turn freely. Make sure that the grinding
tool does not graze against the protection guard or oth-
er parts.
 When operating the machine with power from mobile gen-
erators, loss of performance or untypical behavior can oc-
cur upon switching on.
1 609 92A 2CE | (25.8.16)
 By applying too high application force, the machine can
be subject to overload. Overload can lead to overheat-
ing and damage of the power tool. After heavily strain-
ing the power tool, continue to run it at no-load for sev-
eral minutes in order to cool it down.
 Do not use the power tool with a cut-off stand.
 Never use a cutting disc for roughing.
 The quick-clamping nut may be used only for grinding
or cutting discs. Use only a flawless, undamaged quick-
clamping nut.
 For operations with the rubber sanding plate or with
the cup brush/wheel brush/flap disc, always mount the
hand guard .
 For cutting with bonded abrasives, always use a pro-
tection guard for cutting.
 Provide for sufficient dust extraction when cutting
stone.
 Wear a dust respirator.
 To save energy, only switch the power tool on when using
it.
 Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only: Use a residual current
device (RCD) with a rated residual current of 30 mA or
less.
Symbols
The following symbols are important for reading and under-
standing the operating instructions. Please take note of the
symbols and their meaning. The correct interpretation of the
symbols will help you to use the machine in a better and safer
manner.
Symbol
Meaning
Article number
Read all safety warnings and all instruc-
tions
Before any work on the machine itself,
pull the mains plug from the socket out-
let
Bosch Power Tools

Hide quick links:

Publicidad

Tabla de contenido
loading

Tabla de contenido