Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
1
Set plate
2
Battery cartridge
3
Switch trigger
4
Nozzle
SPECIFICATIONS
Model
Capacity ................................................................600 ml
Continuous use ...............................................8 – 10 min.
Overall length ......................................................365 mm
Net weight ..............................................................0.6 kg
Rated voltage ...................................................D.C. 7.2 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for collecting dry dust.
Safety hints
For your own safety, please refer to the enclosed Safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS
FOR CHARGER & BATTERY CARTRIDGE
1.
Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using battery.
2.
Do not disassemble battery cartridge.
3.
If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4.
If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5.
Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not
used.
6.
Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
7.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
8.
Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
9.
Be careful not to drop or strike battery.
SAVE THESE INSTRUCTIONS.
4
Explanation of general view
5
Extension wand (Straight pipe)
6
Corner nozzle
7
Tap or rap here
8
Capsule
Tips for maintaining maximum battery life
1.
4071D
2.
3.
4.
ADDITIONAL SAFETY RULES FOR TOOL
1.
2.
3.
4.
ENC004-1
5.
6.
7.
8.
9.
10. Always remove the dust case and empty out the
11. When not in use, it should be stored in dry place.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing battery cartridge (Fig. 1)
• Always switch off the tool before insertion or removal of
the battery cartridge.
• To remove the battery cartridge, pull out the set plate
on the tool and grasp both sides of the cartridge while
withdrawing it from the tool.
• To insert the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Snap the set plate back into place. Be sure
to close the set plate fully before using the tool.
• Do not use force when inserting the battery cartridge. If
the cartridge does not slide in easily, it is not being
inserted correctly.
9
Pre-filter
10 Filter
Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the bat-
tery cartridge when you notice less tool power.
Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
Charge the battery cartridge with room tempera-
ture at 10°C – 40°C (50°F – 104°F). Let a hot bat-
tery cartridge cool down before charging it.
Charge the Nickel Metal Hydride battery car-
tridge when you do not use it for more than six
months.
Do not use cleaner close to dangerous flamma-
ble materials such as gasoline, gas, paint or
adhesives.
Do not suck up wet materials.
Do not pick up sticky items.
Do not pick up pins or thumbtacks.
Do not pick up lit cigarettes and the like.
When you suck up a large item and revolution
becomes difficult, immediately switch off the
cleaner and remove it.
Be careful not to let anything enter the exhaust
port.
Do not bring close to stoves or other heat
sources.
Shut off the cleaner the moment you notice any-
thing abnormal in operation.
contents before beginning or after completing a
cleaning job. A full dust case can cause prob-
lems, even a breakdown.
Publicidad
Tabla de contenido
