König DVB-S2 REC11 Manual De Usuario página 5

"Antenna Connection"
"Satellite List"
"Antenna Setup" - "Fixed Antenna"
1. Select "Fixed Antenna" or "Motor
Antenna".
1. Select the satellite. Press the OK
button.
1. Press the red button to open the
"Edit Satellite" window.
2. Edit the satellite.
- "Name": Press the digit buttons
to edit the name. Press the OK
button.
- "Longitude": Select west
longitude or east longitude. Press
the digit buttons to edit the
longitude. Press the OK button.
3. - Press the yellow button to save
and exit.
- Press the blue button to exit
without saving.
1. Press the green button to open
the "Add Satellite" window.
2. Edit the satellite.
- "Name": Press the digit buttons
to edit the name. Press the OK
button.
- "Longitude": Select west
longitude or east longitude. Press
the digit buttons to edit the
longitude. Press the OK button.
3. - Press the yellow button to save
and exit.
- Press the blue button to exit
without saving.
1. Press the blue button to delete a
satellite.
The following message appears:
"Are you sure to delete?"
2. - Select "Yes" to delete.
- Select "No" to cancel.
1. "Satellite" / "LNB Freq" /
"Transponder" / "DiSEqC1.0" /
"DiSEqC1.1": Select the satellite.
Press the OK button.
2. "22K" / "Polarity":
Select the satellite. Press the OK
button.
6 6
"Antenna Setup" - "Motor Antenna"
1. "LBN Type": Select the LBN type. Press the OK button.
2. "Motor Type": Select "DiSEqC1.2" or "USALS". Press the OK button.
Notes:
• If you select "DiSEqC1.2", the menu items "Local Longitude" and "Local
Latitude" will become grey.
• If you select "USALS", the menu item "Delete All" will become grey.
3. "Delete All": The following message appears: "Are you sure to clear set
satellite positions of this tuner?"
- Select "Yes".
4. "Motor Setting":
a) "Satellite" / "Transponder": Select the satellite or the transponder. Press the
OK button.
b) "Position No.&Save": Select the correct value (0-64) when you rotate the
antenna.
c) "Go to X": Select the correct position to realise the selected position.
d) "West <Save> East": Set the longitude. Press the OK button.
The following message appears: "Are you sure to change this satellite's
position?"
- Select "Yes".
e) "Recalculation": The following message appears:
"Are you sure to change this satellite's position?"
- Select "Yes".
5. a) "Limit Setup": Select "Disable Limit", "East Limit" and "West Limit". Move the
cursor to "Limit Setup". Press the left button to turn west or the right button
to turn east.
Notes:
• If you select "Disable Limit", the menu item "Limit Setup" will become grey.
b) "Go to Reference": Press the OK button to confirm.
6. - "Local Longitude": Select "West" or "East". Press the OK button. Enter the
longitude. Press the OK button.
- "Local Latitude": Select "North" or "West". Press the OK button. Enter the
latitude. Press the OK button.
"Single Satellite Search" / "Multi Satellite Search"
English
1. "Satellite": Select the satellite(s).
Press the OK button.
2. "FTA Only": Select "Yes" or "No".
Press the OK button.
3. "Scan Channel": Select
"TV + Radio", "TV Channel" or
"Radio". Press the OK button.
4. "Network Search": Select "Yes" or
"No". Press the OK button.
Note: The menu item becomes
grey when "Auto Scan" is selected
in the "Scan Mode" submenu.
5. "Scan Mode": Select "Auto Scan"
or "Preset Scan". Press the OK
button.
Note: "Auto Scan" is a blind scan,
while "Preset Scan" searches for
preset frequencies.
6. "Search": Press the OK button to
start searching.