Explanation Of General View; Additional Safety Rules For Tool - Makita 2414B Manual De Instrucciones

ENGLISH
(Original instructions)
1 Base
2 Bolt holes
3 Lock button/Lock-off button
4 Switch trigger
5 Screw
6 Spark guard
7 Socket wrench
8 Guide plate
9 Move
10 Hex bolts
11 Shaft lock
12 Safety guide
13 O-ring
SPECIFICATIONS
Model
Wheel diameter ...................................................................................................................................................355 mm
Hole diameter .....................................................................................................................................................25.4 mm
-1
No load speed (min ) ............................................................................................................................................. 3,800
Dimensions (L x W x H)
With under cover..............................................................................................................500 mm x 280 mm x 620 mm
Net weight
With European type safety guide and under cover ............................................................................................ 18.3 kg
Safety class ............................................................................................................................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for cutting in masonry and ferrous
materials with appropriate abrasive cut-off wheel. Follow
all laws and regulations regarding dust and work area
health and safety in your country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
For public low-voltage distribution systems of
between 220 V and 250 V
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under unfavor-
able mains conditions can have adverse effects to the
operation of other equipment. With a mains impedance
equal or less than 0.26 Ohms it can be presumed that
there will be no negative effects. The mains socket used
for this device must be protected with a fuse or protective
circuit breaker having slow tripping characteristics.

Explanation of general view

14 Inner flange
15 Ring
16 Spindle
17 Cut-off wheel
18 Outer flange
19 Hex bolt
20 Vise plate
21 Vise nut
22 Vise handle
23 Spacer block
24 Straight piece of wood (Spacer)
25 Over 45 mm wide
26 Over 65 mm wide
General Power Tool Safety Warnings
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
ENE007-2
Save all warnings and instructions for future refer-
ence.

ADDITIONAL SAFETY RULES FOR TOOL

ENF002-2
1.
2.
3.
ENF100-1
4.
5.
6.
7.
8.
9.
10. Make sure the wheel is not contacting the work-
27 Over 190 mm long
28 Diameter of workpiece
29 Width of spacer block
30 Vise
31 Blocks
32 Under cover
33 Wing bolt
34 Handle
35 Uncut portion
36 Workpiece
37 Limit mark
38 Screwdriver
39 Brush holder cap
WARNING Read all safety warnings and all
Wear protective glasses. Also wear hearing pro-
tection during extended periods of operation.
Use only wheels recommended by the manufac-
turer which have a maximum operating speed at
least as high as "No Load RPM" marked on the
tool's nameplate. Use only fiberglass-reinforced
cut-off wheels.
Check the wheel carefully for cracks or damage
before operation. Replace cracked or damaged
wheel immediately.
Secure the wheel carefully.
Use only flanges specified for this tool.
Be careful not to damage the spindle, flanges
(especially the installing surface) or bolt, or the
wheel itself might break.
Keep guards in place and in working order.
Hold the handle firmly.
Keep hands away from rotating parts.
piece before the switch is turned on.
2414B
/II
GEA010-1
ENB066-1
5