Explanation Of General View; General Power Tool Safety Warnings; Circular Saw Safety Warnings - Makita 5705R Manual De Instrucciones

ENGLISH
(Original instructions)
1 Lever
2 Clamping screw
3 Base plate
4 Top guide
5 Base
6 60° angle cuts
7 45° angle cuts
8 30° angle cuts
9 Straight cuts
SPECIFICATIONS
Model
Blade diameter
at 90°
Max.
cutting depth
at 45°
–1
No load speed (min
Overall length
Net weight
Safety class
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2014
Intended use
The tool is intended for performing lengthways and
crossways straight cuts and miter cuts with angles in
wood while in firm contact with the workpiece. With
appropriate Makita genuine saw blades, other materials
can also be sawed.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
For model 5705R
For public low-voltage distribution systems of
between 220 V and 250 V
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under unfavor-
able mains conditions can have adverse effects to the
operation of other equipment. With a mains impedance
equal or less than 0.37 Ohms it can be presumed that
there will be no negative effects. The mains socket used
for this device must be protected with a fuse or protective
circuit breaker having slow tripping characteristics.

Explanation of general view

10 Blade
11 Setting protuberances
12 Hex socket head bolt
(For adjusting riving knife)
13 Cutting depth
14 Lock-off button
15 Switch trigger
16 Hex wrench
17 Shaft lock
5705R
190 mm
66 mm
46 mm
) 4,800
356 mm
5.4 kg
/II
5903R
235 mm
85 mm
64 mm
4,500
400 mm
7.2 kg
/II

General power tool safety warnings

WARNING Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
ENE078-2
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
ENF002-2

CIRCULAR SAW SAFETY WARNINGS

Cutting procedures
1. DANGER: Keep hands away from cutting area
and the blade. Keep your second hand on auxil-
iary handle, or motor housing. If both hands are
holding the saw, they cannot be cut by the blade.
ENF100-1
2. Do not reach underneath the workpiece. The
guard cannot protect you from the blade below the
workpiece.
3. Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade teeth
should be visible below the workpiece.
4. Never hold the workpiece in your hands or
across your leg while cutting. Secure the work-
piece to a stable platform. It is important to sup-
port the work properly to minimise body exposure,
blade binding, or loss of control. (Fig. 1)
18 Hex socket head bolt
19 Outer flange
20 Saw blade
21 Inner flange
22 Vacuum cleaner
23 Limit mark
24 Screwdriver
25 Brush holder cap
5103R 5143R
270 mm 355 mm
100 mm 130 mm
73 mm 90 mm
3,800 2,700
442 mm 607 mm
9.3 kg 12.5 kg
/II /II
GEA010-2
GEB143-1
5